1. Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L =400 mm, v= 0.35, and E= 70 GPa.a.1.17 x 10-3b. 1.87 x 10-3C. 2.04 x 10-32.36 x 10-3d.a.b.P2. A 300 mm long rod is subjected to 4 kN of tensile force. The allowable stress and deformation is 60 MPaand 0.05 mm. Determine the required diameter of the rod in mm. Use E = 200 GPa.9.5C.11.510.5d.12.5

Answered: Image /qna-images/answer/18c1713b-57e1-4224-ae1a-bfd2d952033f.jpg

Answered: 1. Determine the lateral strain, in…

1. Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L = 400 mm, v= 0.35, and E= 70 GPa. a. 1.17 x 10-3 b. 1.87 x 10-3 L C. 2.04 x 10-3 d. 2.36 x 10-³ P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: - Determine which of these equations have an identical meaning with a = Qijaj ap=Opmam, ap = Qapaq,…

A: Given equation: ai = Qij×a'j

Q: Question 8 The gravity wall is made of concrete. Determine the location (x, y) of the center of mass…

Q: Problem 2. In an air standard diesel cycle, the compression ratio is at the beginning of isentropic…

A: Given Compression ratio = 16 Temperature at point 1 = 15o C = 273 + 15 = 288 K Pressure at point 1 =…

Q: Carbon steel (AISI 1010) shafts of 0.1 m diameter are heat treated in a gas-fired furnace whose…

A: (A) Write the given data. Diameter of shaft, d=0.1 mInitial temperature of shaft, Ti=300…

Q: answer in units of pounds to one decimal point. FHI b H A FEM CFCD b. 3ft 4ft 52 3ft 3ft 52 F1

A: To find force in member CH

Q: 45° 60 mm y 90 mm | 45° 60 mm 75 mm 100 mm X

A: According to the given data There are 5 shape of the combined cross-section We need to find center…

Q: . Determine which of these equations have an identical meaning with a¡ = Qijaj ap=Opmam, ap = Qapaq,…

A: Given equation: ai = Qij×aj' where, Qij is a matrix and aj is a vector. The prime symbol (') denotes…

Q: Plastic materials that soften and melt under exposure to heat and can reach a flowable state

A: A class of plastic materials possess a unique property of softening and melting under the…

Q: find the temperature, pressure, density at 40,000 ft in standard atmosphere

A: According to the given data h=40,000ftWe need to find Temperature Pressure Density

Q: Derive a governing equation of theSDOF System shown under static deflection.

A: Given data:- Mass of block = m Spring stiffness = k…

Q: Problem 2 Determine the cross-section area of members BD. BE. and CE if the stress in these members…

A: The maximum stress while tension is σt=20 ksi. The maximum stress while compression is σc=25 ksi.

Q: A compressed air tank in a service station has a volume of 10 ft³. It contains air at 70°F and 150…

Q: State 1 for a dual combustion engine is P1 = 1 atm and T1 = 60.3°C; rk = 18; at the end of the…

A: Given data:- At state 1 P1 = 1 atm T1 = 60.3o C…

Q: . Determine the displacement gradient tensor, right Cauchy-Green deformation tensor, small…

A: Given: u=AX12X3BX1X2X3CX2+CX32 To find: Displacement gradient tensor Right Cauchy-Green deformation…

Q: 1. Why does a surface composed of a particular material get dirtied? 2. Why do engineering metals…

A: Introduction Engineering metals and alloys refer to materials that are specifically designed and…

Q: 16-22 The inner and outer surfaces of a 0.5-cm thick 2-m X 2-m window glass in winter are 10°C and…

A: Given that: Thickness of glass = 0.5 cm Area of window = 2x2 = 4 m2 Tinner = 10°CTouter = 3°Ck =…

Q: [2] Repeat Example 8.1 (pages 303-305) but with the following exceptions: steam fed to the turbine…

A: Given-Information:- Pressure, p = 9000 kPaTemperature, T = 600°CExhaust Pressure, p = 10…

Q: Make the indicated conversion between customary and metric units of weight and mass. 17…

Q: A hot surface at 100°C is to be cooled by attaching 3-cm-long, 0.25-cm-diameter aluminum pin fins (k…

A: To Find: The rate of heat transfer from the surface. Given : The surrounding temperature is…

Q: Explian forcing a square head in a round hole

A: "Force a square peg into a round hole" is a common idiom used to describe a situation where someone…

Q: 8) A) A rectangular plate with dimensions 3m x 5m is submerged horizontally in a pool of water. Find…

A: “Since you have posted a multiple question, we will provide the solution only to the first question…

Q: Sample Problem 3/15 - 30 000 A satellite of mass m is put into an elliptical orbit around the earth.…

A: Introduction In this problem, we will calculate the velocity of the satellite as it reaches point B…

Q: For flowing water at 10°C, what is the magnitude of the velocity gradient needed to produce a shear…

Q: A three stepped bar has one end clamped (having the largest area) and the other end with the…

A: Given Data: L1 = L2 =L3 =10 mmF = 50 NA(1)=50 mm2A(2)=20 mm2A(3)=10 mm2E=200*103 MPa Find: Calculate…

Q: Problems The beam shown supports a load that varies uniformly from 100 N/m at the left end to 200…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: A spring of stiffness 20 kN/m supports a mass of 4 kg. The mass is pulled down 8 mm and released to…

Q: 59. Figure P4.59 shows a slanted tube connected to a reservoir containing oil and water. If angle of…

A: According to the question data ho=0.6m with sgo=0.89 hw=0.4m with sgw=1 θ=45 Length of the tube=L We…

Q: Cavity flow is generated when a plate is dragged at speed U over the top of a cavity (of height 8)…

A: Given: To find: Fluid stretching and rotational components

Q: The gauge pressure of a pneumatic cylinder reads 40 lb/in.? when the volume is 30 in.3. The cylinder…

A: According to the data P1=40lb/in2 P2=60lb/in2 We need to find Absolute pressure P2

Q: The system of three particles has the indicated particle masses, velocities, and external forces. If…

A: The values are m1=1.2 kg, d1=1.39 m, v1=0m2=2.6 kg, d2=0.74 m, v2=2.5 m/sm3=4.4 kg, v3=1.8 m/s,…

Q: Consider the frame shown in (Figure 1). Suppose that F-310 lb. Follow the sign convention. Figure 3f…

Q: 7-2 The section of shaft shown in the figure is to be designed to approximate relative sizes of d =…

A: Given data: d = 0.75D; D = d/0.75 r = D/20 = d/(0.75×20) = d/15 ultimate tensile strength, Sut =…

Q: On a weather station, an altimeter was calibrated to 35 in Hg while the documented density at sea…

A: “Since you have posted multiple questions with multiple sub parts,we will provide the solution only…

Q: A refrigerator is to operate to maintain a refrigerator temperature of 4°C in a 20ºC kitchen. You…

A: Given data: Tref=4 °CTroom=20 °CΔTheat=5 °C It is required to determine the refrigerant…

Q: The front and side views of a centrifugal impeller are shown in the figure below. All symbols have…

Q: A beam fabricated from western white pine has been reinforced by bonding steel strips on its top and…

A: Givenσwood=1.5ksiσsteel=35.6 ksiL1=10inL2=0.9inL3=5.3in

Q: The company has opted to purchase a new viscometer for you, as such, you are required by to propose…

A: Solution: Given Data: Temperature (°C) = 40, 65, 80, 100 Time (s) = 57, 41, 29, 16 Calibration…

Q: Derive the equation Rom (Interior Node) Tmn +1 +Tmin-1 + Tm+1/n + Tm-tin - 45min =0

A: The following assumptions can be made to simplify the solution: All the nodes are at equal…

Q: Determine the maximum shearing stress and elongation in a helical steel spring composed of 25 turns…

Q: 44. The value of work index does not change materially from one equipment to another. If the value…

A: The value of the work index for close circuit grinding is Wi.

Q: Q5. For a point at distance 50 m and angle 450 to the axis which of the following statements are…

A: The sound field produced by an infinite baffled piston can be described using the following…

Q: Stepwise Solution please. With the help of Maxwell equations prove that the specific heats of ideal…

A: Write the Maxwell equations. ∂T∂Vs=-∂P∂sV ...... (1)∂T∂Ps=∂V∂sP…

Q: Develop a mathematical expression for the effective mass transfer rate achieved by an implanted drug…

A: To find: The mathematical expression for the effective mass transfer rate.

Q: 3. A beam is loaded and supported as shown below. Determine (a) The equation of the elastic curve.…

A: (a) Draw the diagram of beam.

Q: Two couples act on the beam (Figure 1). Figure 1.5h 200 lb 200 lb 125 f 1 of 1 Part A It F=147 lb,…

Q: A flow meter is attached to a hydraulic line that measures 8 gal/min. The line has an inside…

A: According to the given data. D=1.5in V=8gal/min We need to find Flow rate measured in in/min

Q: Vb=5V, R1=4Ω, R2=8Ω, R3=12Ω, R4=16Ω Compute the listed: Equivalent resistance of entire system.…

A: The potential of the battery is Vb=5V. The value of resistors are R1=4 ohm, R2=8 ohm, R3=12 ohm

Q: Q.5) Replace the force and couple system with an equivalent wrench. Note: the 10 N-m couple moment…

Q: What are the elastic modulus (E) and the Poisson's ratio () used to indicate? 2. Illustrate the…

A: The elastic modulus (E) and Poisson's ratio are two important parameters used to describe the…

Q: Find forces of support members (A,B,C, and D) within diagram above

Question

1. Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L =
400 mm, v= 0.35, and E= 70 GPa.
a.
1.17 x 10-3
b. 1.87 x 10-3
C. 2.04 x 10-3
2.36 x 10-3
d.
a.
b.
P
2. A 300 mm long rod is subjected to 4 kN of tensile force. The allowable stress and deformation is 60 MPa
and 0.05 mm. Determine the required diameter of the rod in mm. Use E = 200 GPa.
9.5
C.
11.5
10.5
d.
12.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l' = 10.009 cm. 30 cm 10 cm -F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) |MPa (Express your answer for strain using four decimal spaces.) E = b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final cm
The steel railroad increases its length when exposed to heat from 70°F to 95°F. The coefficient of thermal expansion is 11.7 x 10€ m/m-°C. Find the strain. A. 4.53 x 10-4 B. 2.625 x 104 C. 1.625 x 10-4 D. 3.53 x 10-4
1.2 A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of external diameter 40 mm and 5 mm thick. The composite bar is then subjected to an axial pull of 45 kN. If the length of the compound rod is 150 mm, and the elasticity moduli are Est = 200 GPa and Ecu= 100 GPa. determine: 1.2.1 The stresses in the rod and tube 1.2.2 The load carried by the rod and that carried by the tube 1.2.3 The elongation of the compound rod.
Current Attempt in Progress Arigid steel bar is supported by three rods, as shown. There is no strain in the rods before the load Pis applied. After load Pis applied, the normal strain in rod (2) is 870 uin/in. Assume initial rod lengths of L- 156 in. and L2- 63 in. Determine (a) the normal strain in rods (1). (b) the normal strain in rods (1) if there is a 0.019in gap in the connections between the rigid bar and rods (1) at joints A and C before the load is applied. (c) the normal strain in rods (1) if there is a 0.019 in. gap in the connection between the rigid bar and rod (2) at joint B before the load is applied. Answers: (al e uinvin. (b) e- pin/in. (c) - uin/in.
Rigid bar ABCD is supported by two bars as shown. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (2) is measured as −3,300 μm/m. Use the dimensions L1 = 1,600 mm, L2 = 1,200 mm, a = 240 mm, b = 420 mm, and c = 180 mm. Determine (a) the normal strain in bar (1). (b) the normal strain in bar (1) if there is a 1 mm gap in the connection at pin C before the load is applied. (c) the normal strain in bar (1) if there is a 1 mm gap in the connection at pin B before the load is applied.
Question 2 A 60° strain rosette is installed on the traction-free surface of a component with one of the strain gages aligned along the y-axis, as illustrated in Figure Q2. The gages show the following strain readings upon loading the structure: E, = 925 x10“ ; &, = 740 x10“ ; ɛ. = -555 ×106 (a) Determine the strains in the x-y directions and show the corresponding strain element. (b) Calculate the principal in-plane strains and the corresponding principal directions. Show the principal strain element. (c) Calculate the in-plane maximum shear strain and show the corresponding strain element. (d) If the structure is made of steel with elastic modulus and Poisson's ratio of 220 GPa and 0.30, respectively, calculate the principal stresses. Show the principal stress element. (e) Determine the normal strain in the n-direction. & Ea
Asap
4. Show that Cp = as +45°. principal strain and shear strain
1.4 Derive an expression for the local uniform strain across the neck of a round bar being loaded in tension. Then, determine its magnitude if the original diameter is reduced 80%.
Q.3) A structural member in plane strain has the following strains at a point: & 360 μ , E, = 230 µ, Ky = 150 µ (a) Determine the strains for an element oriented at an angle of 60° counter clockwise. (b) Determine the principal strains and the maximum shear strain using strain transformation equations. (c) Show the result of parts (a) and (b) via sketches of properly oriented elements. Ey Yxy 1 Ex
When subjected to a compressive load, the length of the rod is 199,6 mm, and its diameter is 10 mm. If the original length was 200 mm, and modulus is 70 GPa, determine: 1.1 The stress and strain in the rod when loaded. 1.2 The magnitude of the load.
A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the load Pis applied. After load P is applied, the normal strain in rod (2) is 840 pin./in. Assume initial rod lengths of L1 = 120 in. and L2 = 71 in. Determine (a) the normal strain in rods (1). (b) the normal strain in rods (1) if there is a 0.032 in. gap in the connections between the rigid bar and rods (1) at joints A and C before the load is applied. (c) the normal strain in rods (1) if there is a 0.032 in. gap in the connection between the rigid bar and rod (2) at joint B before the load is applied. (1) (2) Rigid bar Answers: (a) E1 = i pin./in. (b) E1 = pin./in. (c) Ɛ1 = i pin./in.