1. A 2-wire d.c. street mains AB, 600 m long is fed from both ends at 240 V. Loads of 25 A, 45 A, 55 A and 35 A are tapped at distances of 100m, 250m, 400m and 500 m from the end A respectively. If the area of X-section of distributor conductor is 1cm², find the minimum consumer voltage. Takep-1.7 x 10-62 cm.

1. A 2-wire d.c. street mains AB, 600 m long is fed from both ends at 240 V. Loads of 25 A, 45 A, 55 A and 35 A are tapped at distances of 100m, 250m, 400m and 500 m from the end A respectively. If the area of X-section of distributor conductor is 1cm², find the minimum consumer voltage. Takep-1.7 x 10-62 cm.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.17P: Determine the GMR of each of the unconventional stranded conductors shown in Figure 4.30. All...

See similar textbooks

Similar questions

Determine the GMR of each of the unconventional stranded conductors shown in Figure 4.30. All strands have the same radius r.
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
A 30 kV single core cable has a conductor dimeter of 2 cm and a sheath of inside diameter 6 cm. Find the maximum (peak value) and minimum stress (peak value) in the insulation.
A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm. Find the maximum and minimum stress in the insulation.
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The maximum Electric stress of the cable is
One advantages of load balancing is that each phase conductor carries the ? current value
3. What are the classifications of Core Loss and Copper Loss?
i) Calculate V1 and V2 for the voltage across the string insulator having phase voltage of 33kV for transmission line using details tabulated in the Table 3(a). Table 3(a) Type of Insulator Shunt Capacitance between each unit 0.1 C String to junction Self -Capacitance of each insulator ii) With the help of a suitable schematic diagram and necessary theoretical explanation, illustrate how to improve the efficiency of the suspension insulator.
INSULATORS A string of suspension consists of four (4) units. The Voltage between each pin and earth is 0.14 of the Self-Capacitance of the unit. The Voltage between the Line Conductor and earth is 135 KV. Find the Voltage distribution across each unit. Draw the diagram.
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The minimum Electric stress of the cable is
E A 2-wire d.c. ring distributor is 400 m long and is fed at 240 V at point A. At point B, 150 m from A, a load of 150 A is taken and at C, 100 m from B, with load of 40 A and at D, 25m in the opposite direction from A, a load of 200 A is taken. If the resistance per 100 m of single conductor is 0.04 22, find: (i) Current in each section of distributor (ii) Voltage at points B, C and D.
33 kv single core cable has a radius of conductor of 0.6 cm. The insulation martial has two layers. The thickness of the first and second layers are 0.8 cm and 0.4 cm respectively. The relative permittivity of the first and second layers are 4 and 3 respectively. Find 3- The minimum electric stress of the second layer. 4- The minimum electric stress of the first layer.