1) Op-amp limiting factors - Current Saturation U2 Vin ww1₁0 R1 OU] OPAMP R2 w RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax = 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax = 2V, Vmin = -2V) and a period of 2ms.

1) Op-amp limiting factors - Current Saturation U2 Vin ww1₁0 R1 OU] OPAMP R2 w RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax = 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax = 2V, Vmin = -2V) and a period of 2ms.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Op amp and diodes are ideal. Derive Vout and sketch the transfer function of Vin vs Vout. Please show complete solution.
The term duty cycle refers to the amount of time a signal is complete cycle. A. off compared to the period of one B. on The output voltage of op-amp is positive saturation, when the voltage applied to the input is greater than the input. A. inverting B. noninverting A square wave that is 20V at its high state and OV when it is off will produce an average DC when its duty cycle is 75%. Formula: VOUT = Duty Cycle * Peak voltage voltage of A. 7.5V B. 10V C. 15V
Op amp and diodes are ideal. Derive Vout and sketch the transfer curve of Vin vs Vout. Please show complete solution.
For the given op-amp circuit, determine: (a) iout/iin2, (b) iin2/iin, (c) iin/Is, and (d) iout/Is.
2. b) (i) Derive an expression for the differentiator using op-amp. (ii) Design a circuit to perform differentiation of an input signal that varies in frequency from 20HZ to about 2 KHz. (iii) If a sine wave of 0.5 V peak at 2 KHz is applied to the differentiator of part (ii), draw the output waveform.
4) Consider the clamping circuit below, assume Vref=3 V and Vin=5sin(wt) ..Draw the output voltage waveform. Clearly mark the max and min of the voltage.. Vref
Design an op-amp circuit that can perform this operation: Vo = 2V1V2 – 3V3. Marking Scheme: 1. Circuit Diagram 2. Calculation with Assumptions
3) Consider the Zener-diode voltage regulator shown below. Suppose you design this circuit to drive (supply) a load resistance RL. The supply voltages to the op-amp are +15 V and -15 V (not shown). a) What is Vout? b) If R = 1 k 2, what is the smallest R, that the circuit can handle without "sagging" the output voltage? c) What should be the power rating of the resistor R? Be explicit about your assumptions. +15 V R Vout IN4738 CS Scanned with CaScanner
The input voltage for an Op-Amp series regulator is 12v,, if the non inverting input of the op-Amp is connected to 3 series diodes instead of Zener one . a) Design the the op-amp feedback resistors to give 6.5V fixed o/p voltage b) Determine the line regulation in both % and in %/V. if the input voltage increased by 3V leading to o/p voltage increase of 0.05
Suggest a simple op-amp cct to build a Negative Resistor. In other words the resistor seen from the input side is equal to (-R).
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?
Consider the op-amp circuit to the right. Write a general formula for Vout as a function of Vin and the parameters of the resistor and MOSFET. Make sure to pay attention to the orientation of the MOSFET, you may assume an ideal op-amp. Vin R1 om + Q1 Vout