. A coil is to be wound with Q-factor of 8. A lamp rated 120 V, 480 W is connected in series with the coil and connected across 230 V, 60 Hz source. What is the impedance of the coil if the voltage across the lamp is maintained at 120 V. A. 35.2482.9° n B. 27.5472.4° Č.) 45.5482.9° n D. 40.5472.4° LAo inductive coil houing

. A coil is to be wound with Q-factor of 8. A lamp rated 120 V, 480 W is connected in series with the coil and connected across 230 V, 60 Hz source. What is the impedance of the coil if the voltage across the lamp is maintained at 120 V. A. 35.2482.9° n B. 27.5472.4° Č.) 45.5482.9° n D. 40.5472.4° LAo inductive coil houing

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 8RQ

See similar textbooks

Similar questions

3. Two circuit elements in series consume 60 VAR when connected to a 120 – V, 60 – Hz source. If the reactive factor is 0.6, what are the two components and what are their values?
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of the Thyristor (5 µA) and frequency (50 Hz). Find the rate of voltage changing with time and snubber circuit power losses?
PLEASE RESOLVE! THE FINAL ANSWER MUST BE IN THE CHOICES. DC/AC MOTOR (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATIONS NEEDED. ANSWER IN 2 DECIMAL PLACES. BOX THE FINAL ANSWER.) A current of (120-j150) A flows through a circuit when applied voltage is (8 + j12) V. A. What is the magnitude of the circuit impedance: a. 0.0635 ohm b. 0.0256 ohm c. 1.52 ohm d. 1.325 ohm B. What is the reactive power? a. 825.75 VAR b. 525.68 VAR c. 639.75 VAR d. 438.72 VAR
Set the amplitude, phase, and frequency parameters of the AC voltage source block according to the values shown in the figure below
An impedance coil takes 10 A and absorbs 250 W when connected across a 220 V, 60 Hz source. What power will it absorb when connected across 110 V, 25 Hz mains?
Draw rough sketches showing the following:a. A current which lags the voltage by 60 degreesb. A current which leads the voltage by 60 degreesc. A current which lags the voltage by 180 degrees
When a voltage of 100V at 50Hz is applied to an impedance coil A, the current taken is 8A and the power is 120 W. When applied to an impedance coil B, tue currents is 10 A and the power is 500W. What current and power will be talen when 120V, 60 Hz is applied when two coils are connected in parallel?
In a series AC resistive circuit: a) voltage leads current by 90°(degrees). O b) current leads voltage by 90°(degrees). © current and voltage are in phase. d) d current and voltage cancel.
What is the effect on induced voltage of adding more turns of wire to a coil
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.
What is the voltage across the plates of capacitor #1 (C1)? Select one: a. 6.36 volts b. 2.71 volts c. 5.65 volts d. 7.32 volts