Understanding Motor Controls
4th Edition
ISBN: 9781337798686
Author: Stephen L. Herman
Publisher: Delmar Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
thumb_up100%
Chapter 10, Problem 1RQ
Explain the difference between inching and jogging.
Expert Solution & Answer
To determine
The difference between inching and jogging.
Explanation of Solution
Jogging:
Jogging is to start a motor with short nudges of power at full voltage. Jogging should not exceed 5 times in a minute and if frequently done, the starter of the motor will be de-rated.
Inching:
Inching is similar to jogging but at reduced voltage. Inching is to start a motor with short nudges of power at reduced voltage.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Try to explain it in brief.
Fast
11. Bicycle tires for street racing are very narrow. Why aren't they made wider if the bicycle needs to have a large
amount of friction to grip the road during the race? (Your answer must relate to friction, but you may add other
ideas as well.)
skating is an example of
Select one:
O rotating friction
O slipping friction
O Rolling friction
O sliding friction
Chapter 10 Solutions
Understanding Motor Controls
Ch. 10 -
Explain the difference between inching and...Ch. 10 - What is the main purpose of jogging?Ch. 10 - Refer to the circuit shown in Figure 108. In this...Ch. 10 - Refer to the circuit shown in Figure 109. In this...Ch. 10 - Refer to the circuit shown in Figure 107. Assume...Ch. 10 - Prob. 6RQCh. 10 - Prob. 7RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Hello, I want to know the English translation of "flessione e piegamento" according to the movement theory and not as training techniques. In Italian, I distinguish Flexion (flessione), the passage from the long to the short position without load, and Bending (piegamento): the same movement but with the load. Can Flex and Bending be correct?Thanks and best regardsMario Canepaarrow_forwardAnswer is fast please its very urgentarrow_forwardBe quick pleasearrow_forward
- Describe a situation where you might use a Vernier caliper or micrometer. Explain why you would use this measurement tool in the situation you described.arrow_forward1. Is there a difference between the values of Qideal calculated by equation (7) and Qact by using equation (Qaet=Vol/time)? Why? 2. Is there a difference between the values of Qact calculated by equation (8) and Qact by using equation (Qact=Vol/time)? Why? 3. Is there a difference between the values of the ideal diameter and the actual diameter? Why? 4. Is there a difference between the values of Ca calculated by equation (10) and Ca by using equation (11)? Why? 5. What is the relationship type in the plot between the water height in piezometer tube (Ho) and the actual discharge Qact? Why?arrow_forwardhi please solve this mechanical question , i will rate if solved quicklyarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningInternational Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license