The water content of a sample of saturated soil at a mean effective stress of 10 kPa is 85%. The sample was isotropically consolidated with a mean effective stress of 150 kPa. At the end of the consolidation, the water content was 50%. The sample was then isotropically unloaded to a mean effective stress of 100 kPa, and the water content increased by 1%. Given: Gs = 2.7, 'cs = 25°. a) Calculate A and K. 10 b) Determine the failure stresses (p'f and qf) under CU test and CD test for the conditions.

The water content of a sample of saturated soil at a mean effective stress of 10 kPa is 85%. The sample was isotropically consolidated with a mean effective stress of 150 kPa. At the end of the consolidation, the water content was 50%. The sample was then isotropically unloaded to a mean effective stress of 100 kPa, and the water content increased by 1%. Given: Gs = 2.7, 'cs = 25°. a) Calculate A and K. 10 b) Determine the failure stresses (p'f and qf) under CU test and CD test for the conditions.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter11: Compressibility Of Soil

Section: Chapter Questions

Problem 11.4P

See similar textbooks

Similar questions

Please give me right solution according to the question. In a triaxial test on a saturated clay, the sample was consolidated under a cell pressure of 160 kPa. After consolidation the cell pressure was increased to 350 kPa, and the sample was then failed under undrained condition. If the shear strength parameters of the soil are c’ = 15.2 kPa, ϕ’ = 26°, B = 1, Af = 0.27, determine the pore pressure at the failure.
answer 10 onl 1. When consolidation of a saturated soil sample occurs, the degree of saturation A.Increases B.Decreases C.Remains constant D.May increase or decrease 2. The process opposite to consolidation is called swelling, which involves an increase in the volume of the voids due to the water content A.Decreasing B.Increasing C.Equalize D. None of the above 3. OC: is refer to A. An over consolidation ratio as the ratio of the preconsolidation pressure to the present vertical effective stress. (B. A normally consolidated clay is defined as a clay that has a present (in situ) vertical effective stress oo' equal to its preconsolidation pressure oc C. An overconsolidated clay is defined as a clay that has a present vertical effective stress of less than its preconsolidation pressure D. None of the above Сс 4. Coefficient of consolidation of a soil is affected by A.Compressibility B.Permeability C.Both compressibility and permeability D.None of the above 5. The shear strength of a soil…
During Atterberg limit tessts in the Naboratory,the studens obtained the following results froma clayey soil. Wumber of Blows (N) Molsture Content \ 38/4 16 36/5 20 33.1 28 2/7 0 Plastic limit tests: Students conducted two trials and found that PL= 17 2% for the first trial and PL = 18.4% for the second trial. Assume that the liquid limit of the soil iS LL= 29.0% a. Determine the flow index. b. Determine the liquidity index of the soil if the in situ moisture content is 22.0%.
A certain saturated sand (S = 100%) has a moisture content of 27.9% and a specific gravity of solids of 2.61. It also has a maximum index void ratio of 0.90 and a minimum index void ratio of 0.33. Compute its relative density and classify its consistency. (Table on the right) Solution: Given the values of mmoisture content, specific gravity and degree of saturation, the void ratio can be estiamted as: e = Thus the relative density is found to be Dr = • According to the table, the soil is classified as %; soil. TABLE 3.3 CONSISTENCY OF COARSE-GRAINED SOILS AT VARIOUS RELATIVE DENSITIES (data from Lambe and Whitman, 1969) Relative Density, D,(%) 0-15 15-35 35-65 65-85 85-100 Classification Very loose Loose Medium denseª Dense Very dense "Lambe and Whitman used the term "medium," but "medium dense" is better because "medium" usually refers to the particle size distribution.
A CU triaxial test was carried out on a silty clay that was isotopically consolidated using a cell pressure of 125 kPa. The following data were obtained: Axial load (kPa) 0 5.5 11.0 24.5 28.5 35.0 50.5 85.0 105.0 120.8 Axial strain, &₁ (%) 0 0.05 0.12 0.29 0.38 0.56 1.08 2.43 4.02 9.15 Au (kPa) 0 4.0 8.6 19.1 29.3 34.8 41.0 49.7 55.8 59.0 (a) Plot the deviatoric stress vs. axial strain and excess porewater pressure vs. axial strain, respectively. (b) Determine the undrained shear strength (sµ). (Note: we assume that the sample reaches failure). (c) Determine the total principal stresses (0₁,03) and the effective principal stresses (0₁, 03') at the failure, respectively.
2- An undisturbed clay has a preconsolidation pressure of 200 lb/ft. A laboratory consolidation tests yield the following data: o' (lb/ft') e 0.92 3,130 6,270 0.77 a) Determine the void ratio that corresponds to a pressure of 5,800 (Ib/ft). b) Determine the coefficient of volume compressibility for the pressure range stated. c) If C, = 1 x 10* in?/sec, determine hydraulic conductivity, k in in/sec corresponding to the average void ratio within the pressure range.
A CID TXC test was performed on a sample of sand. At the end of consolidation, the back pressure was 140 kPa, and the cell pressure was 340 kPa. At failure, the deviator stress was (ơ1 – 03)f = 200 kPa. a. What was the total pore water pressure, u, at failure? b. Calculate the principle effective stresses, ơi' and os', at failure. c. Calculate the friction angle, d', for this soil.
A sample of moist sand taken from the field was found to have a moisture content of 14% and a porosity of 38%. In the laboratory test that simulates field conditions, it was found that at its densest state, its void ratio is 85% and at its loosest state its void ratio is 40%. Determine the void ratio. Select one: O a. 0.42 b. 0.61 c. 0.79 d. 0.57 It is the densification of soil by removal of air which require mechanical energy. Select one: a. solidification b. consolidation C. compression d. compaction What particular sand is ideal for field density test using sand cone method? Select one: O a. clean sand b. Ottawa sand c. Owatta sand d. white sand
Question 2 The result presented in Table Q2a were obtained from a consolidated drained (CD) triaxial test on a normally consolidated clay sample of 75mm height x 38mm diameter tested at a confining pressure of 50 kPa. Table Q2a. CD triaxial test result Axial strain (%) 1 2 5 10 15 Applied force (kN) 0.01 0.03 0.05 0.08 0.10 Page 3 of 6 (a) Draw the Mohr circle for each stress state in the sample and the total stress path (TSP) throughout the test and determine the slope of the TSP to the horizontal.
A clean sandstone core sample with diameter of 3.8 cm and length of 5.6 cm is saturated with a brine. The core was desaturated in several steps, and the resistance was measured at each saturation. The results are as follows: Water Saturation (Fraction) Resistance (k2) 1.000 1.302 0.900 1.695 0.800 2.283 0.730 2.878 0.640 3.775 0.560 5.637 0.480 7.838 0.375 13.175 0.350 17.050 0.300 26 Brine resistivity= 0.74 Qm Archie coefficient =1.03 Cementation factor= 2.2147 (1) Estimate the rock porosity. (2) Determine the saturation exponent. (3) Estimate the amount of oil and brine (in cc) in the core sample when resistivity index is 5. All steps of the calculations should be shown.
4.15 The following results were obtained from a liquid limit test on a clay using the Casagrande cup device. Number of blows 6 12 20 28 32 Water content (%) 52.5 47.1 43.2 38.6 37.0 (а) Determine the liquid limit of this clay. (b) If the natural water content is 38% and the plastic limit is 23%, calculate the liquidity index. (c) Do you expect a brittle type of failure for this soil? Justify your answer.
The coefficient of permeability of sand at a void ratio of 0.80 is 0.47 mm/s. Estimate the coefficient of permeability of this sand at a void ratio of 0.50.