The variation of pump head, efficiency, and required ENPY parameters with flow rate obtained from the pump manufacturer for the pump considered to be used in the following pumping system is given in the table below. The pump is required to pump from the subaqueous tank to the upper tank at a rate of 6500 lt/min at 40 °C. The diameter of the suction pipe is 16 cm and the discharge pipe is 8 cm, the length of the suction pipe is 6 m, and the discharge pipe is 50 m. The roughness value of the pipe is 0.032 mm. The characteristics of the 3 elbows in the system are the same, and the loss coefficients of the elements causing local loss are given on the figure. The atmospheric pressure at the location where the pump is installed is 101325 Pa. The variation of the pump head, efficiency, and required ENPY at 1450 rpm of a centrifugal pump with a wheel diameter of cm obtained from the pump manufacturer for the pump considered to be used in the system is given in the table below. Y 15 cm

The variation of pump head, efficiency, and required ENPY parameters with flow rate obtained from the pump manufacturer for the pump considered to be used in the following pumping system is given in the table below. The pump is required to pump from the subaqueous tank to the upper tank at a rate of 6500 lt/min at 40 °C. The diameter of the suction pipe is 16 cm and the discharge pipe is 8 cm, the length of the suction pipe is 6 m, and the discharge pipe is 50 m. The roughness value of the pipe is 0.032 mm. The characteristics of the 3 elbows in the system are the same, and the loss coefficients of the elements causing local loss are given on the figure. The atmospheric pressure at the location where the pump is installed is 101325 Pa. The variation of the pump head, efficiency, and required ENPY at 1450 rpm of a centrifugal pump with a wheel diameter of cm obtained from the pump manufacturer for the pump considered to be used in the system is given in the table below. Y 15 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1) Figure Ql shows piping system with pump to drive the oil upward from A (P=PA kPa) to B (P=180 kPa) at a mass flow rate of 3 kg/s. Determine type of flow and calculate required pump power. Given data: oil density and viscosity are 891 kg/m³ and 0.29 N.s/m² respectively. Use Hagen Poiseulli equation for loss: he128µQL/(xpgD“) and Power=Qpghr; Triangle geometry: a²=b²+c² Dripe = 3 mm 15 m Pump 20 m Figure O1
What is the performance of pump (in %, whole number) that supplies 80 gpm of water (80°F) with pressure of145 ft head?
(b) Figure 3 shows a pump with 80% efficiency (no) delivers 50 Liter/s of water at 20°C from tank 1 to tank 2. The pipeline has 150 mm diameter with a length of 200 m made of galvanised steel. Evaluate the input power to an electric motor of 90% (nm) efficiency that connected to the pump. The globe valve used is % wide open. 2 100 m GLOBE VALVE PRESSURE GAUGE МОTOR PUMP
4. A pump is used for the pumping of water from Tank A into Tank B in which the height difference between the surface levels of water is 20 m. The pipe diameter is 400 mm and the pipe length is 2500 m, the coefficient of friction is f 0.0025 and the pump works at a speed of 700 rpm. The characteristics of the pump are shown in Table 4 below You are required to: (a) (10 points) Intepret pump characteristic and system characteristic ina graph. (b) (10 points) Calculate the input and output power at the operating point. 0.1 0.2 0.3 0.35 0.4 0.5 15 17 18 16 14 O30 60 SI83.80 45 H. (m) 11 Table 4: Data of the pump from the Manufacturer
Head, m Consider the plot below, what is the operating flow rate of the pump in this ?system 25 20 15 10 5 0 0.01 0.015 1 0.02 0.025 Q, m³/sec 0.03 - -H-Q curve 0.035 0.04 0.02 m3/s O 0.026 m3/s O 0.32 m3/s O 0.035 m3/s O
Q.2 A centrifugal pump is required to pump water to an open water tank situated 4 km away from the location of the pump through a pipe f diameter 0.2 m having Darcy's frřiction factor of 0.01. The average speed of waterinthe pipe is 2 m/s. If it is to maintain a constant heac of 5 m in the tank, neglecting other minor losses, the absolute discharge pressure at the pump exit is (a) 0.449 bar (c) 44.911 bar dund (b) 5.503 bar (d) 55.203 bar
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
1Two water pumps are arranged in series. The performance data for both pumps follow the parabolic curve fit Havailable =H0 =aV ^2. For pump 1, H0 =5.30 m and coefficient a =0.0438 m/Lpm^2; for pump 2, H0 =8.70 m and coefficient a =0.0347 m/Lpm^2. In either case, the units ofnet pump head H are m, and the units of capacity V are Lpm.Calculate the combined shutoff head. Complete Answer, thank you
If a pump requires a minimum of 2.75 m of NPSHA, how high can the centerline of the pump be located above the top of an open tank that supplies 27 C water to the pump? The barometer reads an average of 732 mmHg throughout the year. The tank is 1.82 m high. The pipe friction is 0.7 m and the velocity is 1.22 ?/? .
An aqueduct is required to supply water to the community.Data: Families = 12 Average members per family = 3 people Breakfast, lunch and dinner = 15 total liters / family Showers = 10lt / person, one daily shower Kitchen wash = 13lts / day Total distance of the pipeline to the storage tank = 1200 meters Total height H from the pump point to delivery to the tank = 70 meters Determine: Estimation of the total volume of the recommended tank, an autonomy of at leas 2 days of storage. It is required to propose a pump that allows at least filling the tank between 5 to 12 hours operation, it must include details of the pump, as well as its curve Image: schematic detail of the proposed system
Q3: Two tank are connected with piping system as shown. If the pump characteristics are given by: hp- 31-120000 and, 7p--190000Q+8590Q Where hp is in meters and Q in m³/s and np is the pump efficiency (%).Estimate the operational cost of the pumping (10000) m² of water to the upper tank if the cost of IKwh is 2000 ID. Neglecting the minor losses. H=15mm 0-150mm
Oil at 38 deg. Celsius is being drawn from a closed tank having a pressure of 70 kPa gage. The level of oil in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48 kPa absolute and its specific gravity is 0.82 Determine the NPSH in meters available. choices: a. 19.36 b. 17.23 c. 4.64