The band-pass filter in the figure is required to pass signals wi th a frequency of f = 59 kHz with a tolerance of 10% (For example, for a 100 kHz operation, the low cutoff frequency fol = 90 kHz and the high cutoff frequency f OH = 110 kHz). Accordingly, when R G1 = 470 Q, R 62 = 560 0, RF1 = 1.2 kO, R F2 = 2 kn, C 1 = 0.05 µF and C2 = 0.03 µF, what should the values of the R, and R 2 resistors be, respectively? (Op-amps would be considered ideal.) Rci RF1 Rc:

The band-pass filter in the figure is required to pass signals wi th a frequency of f = 59 kHz with a tolerance of 10% (For example, for a 100 kHz operation, the low cutoff frequency fol = 90 kHz and the high cutoff frequency f OH = 110 kHz). Accordingly, when R G1 = 470 Q, R 62 = 560 0, RF1 = 1.2 kO, R F2 = 2 kn, C 1 = 0.05 µF and C2 = 0.03 µF, what should the values of the R, and R 2 resistors be, respectively? (Op-amps would be considered ideal.) Rci RF1 Rc:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem D continued b. Determine Vout for the given input signal SIG Rx 20k Ry 5k Vcc o- Vcc/-Vcc +10v/ -10V VOUT -Vcc Rx Ry VREF VSIG (t) 6V -6V VOUT (t)
92 ۱ ۹:۱ ص Qs= 1107 and Qp= 1041 Qs= 1207 and Qp= 1241 Qs= 1007 and Qp= 1041 Qs= 1107 and Qp= 1141 In the figure shown below we can find output current is equal to.. . if the input voltage is equal to 12 mv 12 kO 12 ka 6 ka No option is correct 10 = 32 uA 10 = 34 uA 10 = 38 uA 10 = 36 uA In the fig. shown below we can find the higher critical frequency due to the input
Anti-aliasing filter ensure that are no frequency components greater than entering the system O a. fs/2 O b. 2/fs O c. 2fmax O d. 2fs
Q. For the circuit shown below, find the following 1. The name of this cireuit is 2 The peak secondary voltage (Vru) 3. The peak voltage at the fiter input (Vre) 4. The filternd DC output voltage across R. (Voc) 3. The peak-to-peak ripple voltage at the filter output (Vere) 6. The ripple factor ( r ) 11ov, 50 Hz RL S KO 50
is samples per second. 12. A complex low-pass signal has a bandwidth of 200 kHz. What is the minimum sampling rate for this signal? 13. A complex band-pass signal has a bandwidth of 200 kHz. What is the minimum samnling
H.W: A resistor of resistance R=1000 2is maintained at 17 °C and it shunted by 100 uH inductor. Determine the ms noise voltage across the inductor over a frequency bandwi dth of: Ans: 182 x10° volt Ans: 9.22 x10 volt Ans: 2.34 x10 volt i) 15.9 kHz ii) i) 159 kHz 1590 kHz
Filter for power supply can be in fom of A.LC filter B.RC filter C.RL filter D.air purifier filter
the signal is sampled at a rate of FS. Determine the alias frequencies in the recorded data set if Fs=40Hz Fs=22Hz Fs=20Hz
The following data shows the output voltage of an active filter versus frequency Vo=F(f). Determine the cutoff frequency or frequencies? F(Hz) 100 500 1 K 2 K 5 K 10 K 15k 20 K 30 K 50K 100k 200k 300k VOV) 0.01 0.035 0.07 0.15 0.32 0.51 0.57 0.57 0.49 0.35 0.10 0.05 0.01
What is the difference between bandwidth and bitrate in optical communication engineering
%3D ban d pass filter if f.= 500H2 and For uf2= 1000 Hz a
Calculate the cutoff frequency for the opamp Sallen-Key 2nd order highpass filter