The assembly consists of two posts AD and CF made of A-36 steel and having a cross-sectional area of 1000 mm2, and a 2014-T6 aluminum pos BE having a cross-sectional area of 1700 mm2. If a central load of 400 kN applied to the rigid cap, determine the normal stress in each post. There is small gap of 0.09 mm between the post BE and the rigid member ABC. (Figure 1) ?AD, ?CF, ?BE =

The assembly consists of two posts AD and CF made of A-36 steel and having a cross-sectional area of 1000 mm2, and a 2014-T6 aluminum pos BE having a cross-sectional area of 1700 mm2. If a central load of 400 kN applied to the rigid cap, determine the normal stress in each post. There is small gap of 0.09 mm between the post BE and the rigid member ABC. (Figure 1) ?AD, ?CF, ?BE =

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.4.5P

See similar textbooks

Similar questions

Q4\ Which of the following is a zero-force member? 3 8KN 4 G 4 エ子c D. 4 B AC BD IF ID
4 - For the beam loading configuration and cross-section shown below, what is the maximum allowable load P given that the maximum allowable stress (in tension and compression) is 120 MPa? PO Р 1.6m PN ż 0.8m 0.8m P80 1.6m Р 30 30 T 10 dimensions in mm beam cross-section (same as problem 3, but inverted)
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P 20 KN is applied. Sheel E200 GPa L-1 m 2.0 m 0.6m 1.5m P-20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the axial load at steel rod in KN?
De term ine the kin d and am ount of stress in e ach mem ber of the truss shown by the method of jo in ts in figure P 5-2 (page 76).- 1000lb 1000lb 1000lb 1000Ib 1000 Ib U. h = 20 ft 500lb 500 Ib L. L. RAV 6 pane ls at 10' - 6 ft RBy Note: 1. F o llo w strictly the lecture notes g iv en. Draw the FBD of e ach jo in t 2. Sum m a rize and tabu la te your answers. 3. Compu te the bar forces up to member U,L3 on ly because the truss lo a d in g is sym metric aland the bar forces of right sid e members are id en tic al w ith th e left s ide members. But you in c lu de th e rig ht sid e mem bers in have to the tabu la tion. 4. Show the com puta tio n ho w the leng th s were obta in ed. 5. Look for your own data in the table provided. 6. Copy the problem , data of problem and fig ure of the proble m TABULAT ION FOR SUMMAR Y OF COMPUTATION OF BAR FORCES METHOD OF JOINTS (PROBLEM P5-2 PAGE 76) Mem ber Identification Length Bar Forc e Туре of ft Ib force LOL1 10 3750 Tensio n L1L 2 10 Tension…
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. Steel E200 Gra A-600mm L-I m 2.0 m 0.6m 1.5 m D. V P-20 KN Aluminum E-70 GPa A-900mm L-1.5 m What is the axial load at aluminum rod in KN?
Principle of superposition The beam is indeterminate to the first degree. Force in member BD is chosen as the redundant. This member is therefore sectioned to eliminate its capacity to sustain a force. 60 kN/m 3 m 1.8 m 60 45 actual structure (a) 160 kN/m B FaD redundant рrimary structure ARD FRp applied Fap D
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
954. The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992 steel tube BC. When no laad is applied to the assembly, the gap between end C and the rigid support is 0.5 mm. Determine the support reactions when the axial force of 400 kN is applied. 400 mm 400 kN A992 steel So mm S00 mm 25 mi2014-T6 aluminum alloy Section a-a
Solve for the EI A using conjugate, beam method 3m 50 kN 2m EID @ pt. C 60KN die 2.5m å
A steel pipe (1) is attached to an aluminum pipe (2) at flange B. The pipes are attached to rigid supports at A and C, respectively 18 m 14 m Member (a) has a cross-sectional area A,-3,600 mm2, an elastic modul as a cross-sectional area A 3,600 mm2, an elastic modulus E-200 GPa, and an allowable has a cross-sectional area A2 2,o00 mm2, an elastie modulus E-70 GPa, and an allowable normal stress of 120 MPa. Determine the maximum load Pthat can be applied to fange B without exceeding either allowable stress