Replace all force -couple system by single force act at A. 240N/m R- 255. 255.415 MA- - 848.5234.P 525N.m 175N 600N -1m 45 1 m
Q: *11-16. Determine the moments at B and D, then draw the moment diagram. Assume A and C are pinned…
A:
Q: cross section. Before the slab wa Compute the axial force in each modulus of elasticity.
A: Solution-δB =δC +δ2δ2 =δB -δCδ16 =δ22 δ1=3δ2 δA = δC + δ1 = δC + 3δ2δA =δC+3δB-δEδA…
Q: Q1: A space 16 mm wide between two large plane surface is filled with SEA 30 lubricating oil (0.18…
A:
Q: Mz = 595 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross…
A:
Q: F 26 2 C S X 2 B A solid bar S (E-200 GPa, A=100 mm²) is attached to a cantilever beam (E-200 GPa,…
A:
Q: 12-18. Determine the moments at each joint of the frame, then draw the moment diagram for member…
A:
Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…
A:
Q: According to a construction company plan, a project must be implemented in three consecutive stages…
A: Let, The probability of first stage completed on time (E1) = 0.5 The probability of second stage…
Q: Txs Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an…
A: Given data:- σxA,B=59.2σsA,B=118.5τxsA,B=118.5 Below diagram is given;
Q: A cantilever beam, 6m long, fixed at point A and free at point B, is subjected to a downward uniform…
A: Given data:
Q: 11-23. Determine the moments acting at the supports A battered-column frame. Take E = 29(10³) ksi,…
A:
Q: A loaded pin-jointed truss is shown in the given figure. The force in member AC is (a) 10 √2 kN…
A:
Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 27800 ksi] bars (1) and (2) are…
A:
Q: The solid 37 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the…
A:
Q: Consider a 180-mm-long segment of a simply supported beam. The internal bending moments on the left…
A:
Q: -4/2- B -²/1- …….
A:
Q: The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain.…
A: The given data is shown below: εx=-400μεεy=-295μεγxy=1150 μrad
Q: Draw the frontside and topview the Shape Shown
A: Asked: To draw the front, side and top view of the given shape. The required engineering id drawn…
Q: Find the discharge velocity of soil in cm/min.
A:
Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…
A:
Q: Figure P2.33 shows a portion of the H,O-NaCl phase diagram. 10 Liquid (brine) Salt Ice + -10 F…
A: Draw the portion of the H2O-NaCl phase diagram as given below, a) The two tie lines T1 and T2 at two…
Q: A truss is made up of members with equal lengths. Area of members in compression is 1200mm² and…
A: Determination of Stress in members of truss DF and FH####
Q: The simply supported beam consists of a W530 × 66 structural steel wide-flange shape [E = 200 GPa; I…
A: Given, Section W530 × 66 E = 200 GPa I = 351×106 mm4 Moments ,MA=350 kN-mMD = 155 kN-mLoads,w = 150…
Q: A 6° curve (measured at the centerline of the inside lane) is being designed for a highway with a…
A:
Q: Calculate the hydraulic conductivity of the soil in cm/sec. Determine the seepage velocity, in…
A:
Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…
A: Aluminum EAl = E1 = E2 = 71 GPA d1 = d2 = 17 mm Steel Es = E3 = 190 GPA d3 = 18 mm
Q: The torsional assembly consists of solid 2.9 in. diameter aluminum [G = 4,000 ksi] segments (1) and…
A:
Q: A big box retail store is built with CMU bearing walls around its perimeter. The store measures 450…
A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…
Q: . Design and activated sludge process to treat 10MGD of domestic sewage having a BODs of 210…
A: Data given-Q0 =10 MGD = 37854.12 m3/d SS =10 mg/lSo =210 mg/l Xt =10,000 mg/l Qc =…
Q: 42 January 43 February 77 March 77 April 43 Oscillate May Gradual increase Dramatical rise Remain…
A: As during February to march there is sudden increase .
Q: Assume that gasoline is burned with 99% efficiency in a car engine, with 1% remaining unbumed in the…
A: Given:- efficiency=99% remaining =1% engine =16 kg MW=30 MW=100 To find:- fraction of VOCs
Q: 11-22. Determine the moment at joints A, B, C, and D. then draw the moment diagram for each member…
A: Given data:- Supports A & B are fixed
Q: A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation…
A: Answer We are given Flow rate Q = 500 l/s Elevation of suction reservoir = 65 m Elevation of…
Q: El. 200 mA A Res. H-W Pipe B Pipe E pipec → Negleet minor losses → Pipes B, C, and E are all have: L…
A: Vc = 5m/s
Q: An aluminum alloy pipe with an outside diameter of 5.7 in. and a wall thickness of 5/16 in.…
A:
Q: A road in a hilly terrain is to be laid at a gradient of 4.5%. A horizontal curve of radius 100 m is…
A: given- radius R=100 mgradient=4.5%
Q: What is the maximum population that can be served by an 8-in. sanitary sewer laid at minimum grade…
A: Answer Calculation of Maximum Population that can be served We are given Diameter of sewer drain 'd'…
Q: 45 40 35 30 25 20 15 10 5 0 2.3 The figure below shows "greater than" ogive graph for a set of data…
A: This is a greater than ogive curve. It describes the how many samples are greater than the specified…
Q: From a known point V (vertex), the tangent lines of a compound curve are drawn - having azimuths…
A: *Multiple questions* As per our guidelines we are supposed to answer?️ only one question. Kindly…
Q: Prob3 Determine (a) the difference in pressure and (b) the differ- ence in piezometric head between…
A:
Q: 3. A 50 m tape was standardized and found to be 0.0015 m longer at an observed temperature of 31.5°C…
A: As per metioned above, I have solved question no. 3 Appreciate if there is detailed work with…
Q: The amount of cement (kg) in 1 m3 of mortar with the mix (1:2) is definitely than that in 1m3 of…
A: Given - MCQ
Q: CW Determine the force in member BF. 6x 20 A 3m C 24KN! 3m D E 14m 4m 12KN →12KN F
A:
Q: Distinguish between skewerness and dispersion?
A: Brief concept introduction- skewerness and dispersion- These two terms are very important in the…
Q: Determine the seepage velocity, in cm/min, if the porosity of soil is 0.30
A:
Q: 67. A strip footing is to be designed to carry a gross load of 900 kN/m at a depth of 1 m in a…
A:
Q: A 3.5% grade passing at station 49+45.00 at an elevation of 174.83 ft meets a -5.5% grade passing at…
A: G1 = 3.5% = 0.035 G2 = -5.5% = -0.055 Let L be the length of curve.
Q: The periodic time (T) is given by (where, w Angular = velocity of particle in rad/s.) (A) w/2TT (B)…
A:
Q: Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each…
A:
Q: a Tieback anchor WA WC !!!! C B Soldier beam A L
A:
Step by step
Solved in 3 steps with 3 images
- Questions kasainta05h_chp16.17m What is the fixed end moment FEMAB for the beam with a settlement of 25 mm at support C? 20 kN/m 60 kN 5. E D -8 m+am+4m 7. -8 m El - constant E= 70 GPa /= 800 (10) mm 10. O 713 kN-m O0.1913 N-m O 230.0 N-m O a 106 7AN-mIf P= 60 N, a) Determine the resultant of the force-couple system acting on the frame if it acts at G. b) Determine the location of the resultant if it is to be located on line FG and line GH. Express this location with respect to point Cou 120 N 240 mm 200 N This shared 15 70° G. D 50 mm |42 Ν.m 80 N 520 mm 40 N-m 180 mm Hi |B 50 mm G A 50 mm 640 mm60N LO 30 Nm, CCW 30 Nm, CW Q 270 Nm, CCW 270 Nm, CW LP L C. 1. Which of the following gives the moment of the 90.0 N-force about the center of the circular plate, 0? 44 510 N-M 2. Which of the following force and couple set acting at point O is equivalent to the given forces applied to the circular plate? 3. Which of the following single forces is equivalent to the given forces applied to the circular plate? A. B. B. 570 N-M 224 N 40° 231N 3m 150N 33.8⁰ 27.4° A P 90N LO D. А 44 1150 N-M 1150 N-M SON P 224 N 231N 33.8⁰ 27.4° P P A. LO 27.4⁰ 231 N C. 3m 33.80 231 N O O 2.28 m L D. L 56.20 224 N 33.8° 224 N A O 2.28 m 2.28 m
- [Q5] ( problem 3/20sp134) reactions رسم السؤال Determine the at the pin A" and the roller E'r if (p= 500N). Ane Ax = 1285N, Ay=2964N, 4000 N 30% B 3 m 4 m 4 m %3D E = 3285 N. %3DDraw the FBD of member ABC 160 шн 90 mm 240 N 180 mm B 320 mm D. 125 mm 300 mm- Draw the FDBS of member ADB and BEC 1 m 1 m В 1 m D 1.6 m ASAQ 3 Determine the force-couple system acting at point 0. y 50 N 90 N C 40° B 40 N m 400 mm 1300 mm A 4 800 mm A 100 N 3 Answers: R = 83.4 N, 35° S of E, C = 87.4 N m, CW Ww 009 500 mm-
- 2. (a). Obtain the total elongation of a steel bar of cross-sectional Area 1250mm2 acted upon by forces indicated in the diagram below. E-205,000N/mm2 15N- 5N 20N 40N 15N 1.5m 1.5m 3m Im TAt man Im 12. 5omx7 (2 cis (4 cis A. 1+√3i B. √3-i C. √3 i 4. The expression (į47 — į²¹ + į6² + į8⁰ – i)² when simplified is A. 1 B. i C. -1 3. Evaluate D. -√3+ i D. -iDetermine the moment at point B and point D of the beam 76416 Y B A */0in # -15in- C A 152916 D DOOD 1010-4