Provide state table for following state diagram, and design the mealy machine circuit diagram.

Q: 41 4) obtain the analysis of the synchronous sequential circuit (State table and state diagram) in…

A: Output depends upon present input and present state hence it is mealy machine.

Q: The nominal speed of a construction machine with an operation is 1000 rpm, and when the speed of the…

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: Explain with neat sketch, how electrical energy is produced from the wind energy in WECS?

A: Wind energy conversion systems (WECS) are specially created system which are designed to convert the…

Q: 3. Provide an appropriate reason for the mismatch of theoretical and practical results

A: Theoretical result : theoretical values are measured by using certain theorem and laws they are most…

Q: Q1/ Design a circuit using an arduino board to control the direction and the speed of rotation of DC…

A: Design a circuit using an arduino board to control the direction and speed of rotation of DC motor…

Q: What is the reason for using numerical methods?

A: Reason for using numerical.methods

Q: Define stepper motor a. Explain the internal structure of stepper motor b. With Table explain the…

A: Stepper Motor Also called step motor/Stepping motor Brushless synchronous DC electric motor split…

Q: Write the basic idea of a WECS

A: In this question we need to write the basic idea of WECS ( wind energy conversion system )

Q: h a labelled diagram of any DC machine  Discuss it part

A: A self-excited DC shunt motor, also known as a shunt wound DC motor, is a form of self-excited DC…

Q: Type your question here • Analyze this circuit. • What about the output? • This circuit is an…

A:

Q: write a report about a comparison between state machines. In which, where we can use each type of…

A: There are two types of finite state machines. (a) Mealy state machine (b) Moore state machine…

Q: What is Repeated Measures?

A: There are many measurements of every subject in repeated designs and all subjects are distributed to…

Q: How many modules are present TERCO PST Simulator? Write their names.

A: There are 10 modules of TERCO PST Simulator.

Q: Is the PEC a law? What is a small appliance branch circuit?

A: Small appliance branch circuit: This circuit is used for mainly in the kitchen area and not used for…

Q: e the slots of the armature core of dc ake an improvement on it, for example, make 2 why ?

A: Back EMF equals to applied voltage.

Q: Increasing the length of the air gap of DC machine reduces the Armature reaction effect. Select…

A: In this question, we will see effect of length of air gap on armature reaction...

Q: What is Adaptive control system? If the process characteristics are not well known then what type of…

A: Adaptive control system is the control method which is used by a controller and which must adapt to…

Q: What is the difference between a Moore and Mealy machine? Sketch example state diagrams of each.

A: Moore Machine- In this machine, the machine reacts faster to inputs. In this machine, the output…

Q: n which year did 3D printing first become available to the public?

A: The idea of 3D printer was pitched in 1981 by Hideo Kodama of the Nagoya Municipal Industrial…

Q: 4. What is the objective of a task risk analysis? a. To control the risks associated with the work.…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Is it Inverter is important in solar power system? Why?

A: Inverter is a device which converts the DC supply into AC supply. As we have the storage batteries…

Q: (1) THE CONSTRUCTION OF DC MACHINE Aim: A simplified sketch of a dc machine and describe the…

A: DC Machine is further divided as DC Motor (which converts Electrical Energy to Mechanical energy )…

Q: Decreasing the length of the air gap of DC machine reduces the Armature reaction effect. Select one:…

A: A Brief About Armature Reaction:- The effect of magnetic field produced on the main field flux is…

Q: Explain the Construction and Applications of DC Machines.

A: Construction of a DC machine: The DC machine consists of two main parts: Stator and Rotor 1. Yoke:…

Q: round intermediate calculations. Round your answer to 2 decimal places.) y, the PCB machine produces…

A:

Q: Give some applications for the AC-AC voltage controller. Can this controller be a substitute for…

A: The AC supply is available at the power supply. There are different loads present which require…

Q: create an up counter written in verilog and running the simulation and test bench using the EDA…

A: To create the up counter using verilog :

Q: Q1.Explain temperature compensation of strain gauge in detail?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: What is a simulator? What are advantages of simulation in electrical power system?

A: The solution can be achieved as follows.

Q: What can open-transition starting cause?

A: Open transition starting is a method of getting motor to its rated voltage by reduction of applied…

Q: Write a report on system control strategies and techniques used in engineering.

A: The term system control refers to the controlling of any system. In terms of electrical system, it…

Q: Can we find regulation of a salient pole machine by this test? Justify your

A:

Q: Discuss two design considerations when selecting a stepper motor.

A: When choosing a stepper motor for your application, it is important to analyze the motor’s…

Q: What site or software application was being used for this simulation?

A: Since it is only asked to give the name of the site or software which is being used for the given…

Q: Draw the DC Machine and label its parts

A:

Q: What is the function of the assembly program?

A:

Q: In control, what is the effect of changing the type of the system and the input signal on the…

A: By changing the type of system steady state error wil change. For type 0 system if applied unit step…

Q: What is reverse engineering and how does it work?

A: Reverse engineering is a method or procedure to the products which are already existed. In this…

Q: a) What are the performance specifications that the closed-loop con system will describe? b) Draw…

A: Transfer function:  The ratio of the Laplace transform of output to the Laplace transform of input…

Q: Jo S Q아 J1 Q1 4. FF FF Ko R O아 K1 R. 10 ICO

A:

Q: Define the on grid inverter components and the factors affect its performance ?

A: On grid inverter - The on grid converter is a power converter that converts direct current (DC) from…

Q: what is nameplate reading on machine ? what inferences can be drawn from it ?

A: Nameplate reading tell us, at which voltage the machine is made to operate. Nameplate defined…

Q: Discuss about NUMERICAL SOLUTION OF SWING EQUATION

A: This problem is based on the SWING EQUATION in power system.    Discuss about NUMERICAL SOLUTION OF…

Q: The positioning block diagram of the welding tip is given in the following figure. Of the system…

A:

Q: How do you do Routh Houritz criteria? What is a method that always works? Like how apply to below?

A: