Problem 5: The lap connection shown consists of a PL1/2"X3" plate connected to a ½ in gusset plate with ¼" longitudinal fillet welds as indicated. The plates are A36 steel and the electrodes are E70XX. Calculate the length L (in) of the connection to develop the full capacity of the plate. Hint: The full capacity of the plate will depend on the governing strength of the tension member. Neglect block shear. Use ASD 6" x 1/2" [ P L 1/4 1/4 E70 P - 1³¹x 3" x 1/2"

Problem 5: The lap connection shown consists of a PL1/2"X3" plate connected to a ½ in gusset plate with ¼" longitudinal fillet welds as indicated. The plates are A36 steel and the electrodes are E70XX. Calculate the length L (in) of the connection to develop the full capacity of the plate. Hint: The full capacity of the plate will depend on the governing strength of the tension member. Neglect block shear. Use ASD 6" x 1/2" [ P L 1/4 1/4 E70 P - 1³¹x 3" x 1/2"

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.3.6P

See similar textbooks

Similar questions

The connection is shown in Fig. 3. Two cover plates are applied to connect the steel plates by fillet welds. The dimensions of connection are presented in Fig. 3. The leg size of fillet weld hr is 10 mm. Q235 steel, f-215 N/mm2, E43 electrode, fav=160N/mm?. Calculate the load-carrying capacity of the fillet weld connection wwww. (Note: the strength of steel plate should be calcualted. (Unit: mm) 220 ス20 091
Two steel plates, each 400mm wide and 12mm thick, are to be joined together by a lap splice (single). The electrode to be used for the weld has a nominal tensile strength of 550Mpa. Determine the following:a. the maximum weld size that can be usedb. effective net area of the fillet weld using the maximum weld size allowed by the manualc. the maximum load that can be resisted by the weld using the maximum weld size allowed by the manual.
Problem 7: The load that will be applied to the connection shown has a live load - to - dead load ratio of 3.0. Investigate all limit states. All structural steel is A36, and the weld is a 1/4-inch fillet weld with E70 electrodes. Note that the tension member is a double-angle shape, and both of the angles are welded as shown. Use ASD. Determine the following. 5" 5" 2L5 X 32 X 5/16 LLBB -t = ³/8" Maximum service load that can be applied without exceeding the allowable capacity on yielding on gross area of the tension member (double angle). Maximum service load that can be applied without exceeding the allowable fracture on the net area of the tension member (double angle). Maximum service load that can be applied without exceeding the allowable block shear strength. Considering the weld metal and base metal strength, calculate the maximum service load that can be applied.
A welded bracket connection is shown in figure. It supports a factored load of 150 kN at a distance of 120 mm from the face of column. Design the fillet weld on two sides. Grade of steel = Fe410, f. = 250 MPa. y 120 mm P₁ = 150 kN Fillet weld t = 12 mm
The welded frame beam connection consists of the framing angle 100 x 75 x12.5mm and the column W12 x 72. The welds are 9mm fillet welds made with E70 electrodes. All members are A36 steel. 12.5 mm a.) Determine Pu base on the capacity of the welds. Use LRFD design Factors. W 12x72 Angular Section 75 m 18.75 18.75 Angular section Angular section 800
An I-section bracket is connected to the column as shown. The size of weld is 6 mm on web and 10 mm on flange. What will be the safe load (in kN) that can be carried by the connection? Assume NA for whole weld = 110.57 x 106 mm4. Use Fe410 grade steel. 240 mm 170 mm P unu 00t * 280 mm unu 00t 280 mm
The bracket shown is welded by an E70 electrodes fillet weld and is subjected to a factored load Pu=290KN a.) Determine the polar moment of inertia of the group of welds. b.) Determine the max force per mm to be resisted by the weld as shown. c.) Determine the fillet weld size required for the connection. P = 290 kN 175 mm 150 mm Channel Section 500 mm Welding at the back of the channel
Using SMAW process, E70 electrodes and an A572 steel. Determine the length of the side fillet welds for the full capacity the 125x100x10mm angle tension member as shown below. Assume that the member is subjected to repeated stress variations making any connection eccentricity undesirable. Check the block shear strength of the member. Assume that the WT chord has sufficient strength to develop the weld strengths and the thickness of its web is 12mm. Use U=0.87 for class use and LRFD Method only. L125x100x10 V WT BOTTOM CHORD (please solve completely and neatly thank you so much) 12S
Q2-: The two (4x4×3/8) angles shown below are connected by 4 in E70XX fillet welds to a 5/8-in thick gusset plate as indicated. The angles and gusset plate are fabricated from A36 steel. Determine the tensile force that may be applied to the connection. The applied load is concentric with the weld group. 5/8-in plate 1/4 4x4x 3/8-in angles P- 1/4V 6" E70
1. Design the fillet weld connection between the double equilateral angle steel and gusset plate shown in the figure. The steel is Q235B while the welding rod is E43, then the design value of weld strength f, is 160 N/mm², and the size of fillet weld hf is chosen as 8mm. If the axial force N = 1000KN, please calculate the effective lengths of the side fillet welds on both sides of angle steel under the condition of (1) two side welding is used, and (2) three side welding is used, respectively. t=12 N 2L125X10
Provide a balanced welded connection to mobilize the full capacity of the angle. ( Filler material :fy = 480 MPa, fu = 560 MPa, Members are S235) a Section a-a 10 mm 10 cm P { =37.14 mm 5 cm 16 mm Gusset Plate a
A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back of the channel. All steel is A36 with Fy=250 MPa and Fu=400 MPa. Use E70electrodes having and Fu=485 MPa (SMAW) process. The maximum length of lap is 250mm. The size of fillet weld is 8mm. Assume the width of slot weld is 22 mm. Size of slot weld is 13mm Properties of C250x37 A = 4750 mm2 tw = 13.0 mm2 d = 254 mm a. Determine the force resisted by the slot weld in kN, when the full tensile capacity is 712.5 KN (from the gross yielding capacity using ASD) Hint: Full tensile Capacity = Force Resisted by Fillet and Slot Weld Round your answer to 3 decimal places.