line currents. 3. Two balanced 30 loads are connected across a 230 V, balanced 30 ABC source. Load 1 dissipates 12 KW at 70% p.f. lagging. The combination of these two 30 loads draws 20 KVA at 82% p.f. lagging. If loads 1 and 2 are connected in delta and wye respectively, find: (a) The line currents of each 30 load; (b) The total line currents; (c) The impedance/ of each 30 load. 4. A balanced 36 vorn loadin

line currents. 3. Two balanced 30 loads are connected across a 230 V, balanced 30 ABC source. Load 1 dissipates 12 KW at 70% p.f. lagging. The combination of these two 30 loads draws 20 KVA at 82% p.f. lagging. If loads 1 and 2 are connected in delta and wye respectively, find: (a) The line currents of each 30 load; (b) The total line currents; (c) The impedance/ of each 30 load. 4. A balanced 36 vorn loadin

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Similar questions

)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
5. The figure below shows two star connected loads with three phase power. The voltage source is 120Z0°. The loads are Z₁ = 10 + j4 № and Z₂ = 2 +j3 №. The cables are negligible. Calculate: a) the line and phase current. b) the real power from the source. c) the reactive power of the circuit. Is V N Z₁ Z₁ Z₁ Z₂ Z₂ N N Z₂
A balanced load is connected in star across a 3 phasec415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inducrance 0.5 henry in paeallel with a purw resistance of 28 ohms and a pure capaciror of 60microfarads capacitance ,in each branch. Calculate a. The line currents? Need full working and answer has to be 9.3A Formola for inductance XL= 2×3.142FL FORMOLA FOR CAPACITOR XC= 1/2×3.142×FC
Three single-phase transformers are connected into a three-phase bank. The primary is connected as a wye, and the secondary is connected as a delta. If 4160 V is connected to the primary, what is the phase voltage?
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
Three single-phase transformers (ideal) are connected as shown in the figure below to supply a balanced 3-phase, 150 KVA, 600 VL load from primary 4.16 KVLL line. H1 X1 H2 X2 BALLANCED H1 X1 THREE PHAGE LOAD H2 X2 H1 X1 X2 (a) Draw (neatly) a phasor diagram showing the three, primary line-to-line voltages and the six secondary phase and line voltages. What is the phase relationship between the primary voltage VAB and the secondary voltage V12? Indicate on the phasor diagram:f
2. For the following system shown in the figure, calculate: a. The current through each phase of the load. b. The total real and reactive power of the three-phase load. c. The power factor at the load side. A 220 V 20° 220VL-120° U8 vol 152 I 220 VI20° 9. M.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the real, reactive, and apparent powers seen at load 1? Give also the power factor.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)