For each set of ac phasors, find the indicated resultant. 10. RC series circuit: VR 8 20° V, Vc 5 Z-90° V; resultant VT
Q: VIN VD- R₁ W VD+ R3 R₂ A R4 VOUT
A:
Q: The Laplace transform of an impulse
A:
Q: Find the total resistance between a' and 'b' for the circuit given below. 20 Ω 162 wwww Rab 18 Ω 20…
A: The total resistance of the circuit can be obtained by considering the parallel and series connected…
Q: A system is represented by the transfer function Y(s) R(s) = T(S) The state variable representation…
A: The given transfer function is YsRs=s+3s3+6s2+12s+8. We need to determine the state space…
Q: What is the value of E in each HDL block, assuming that RA=1?Verilog (block and nonblocking…
A: Verilog (block and nonblocking operators) 1. RA = RA − 1; // This is a blocking statement so value…
Q: The following readings are obtained when doing a Break test on a d. c. shunt motor: - Spring balance…
A: Reading of DC Shunt motor with, Spring Balance Reading = Tight Side(W1) = 30.5 kg.…
Q: 1) In the circuit in Figure 6, use the nominal values to solve for the circuit current's magnitude…
A: Given parameters : Voltage supply, Vs = 5∠0 Vrms Series resistance, R = 1-kilo ohm Series…
Q: A 400 V, 3-phase, 4 wire system supplies resistive loads between each of the three lines and…
A:
Q: In VCC is connected to pins 3 and 8 so that the 7-segment LEDs will light when a low signal (ground)…
A: Given & to find: In ........, VCC is connected to pins 3 and 8 so that the 7-segment LEDs will…
Q: (b) Figure Q.2(b) shows the power derating curve for a power transistor. It is rated for a maximum…
A: Given : Power dissipation PD is 115 W Case temperature TC is 25°C Derating factor is 0.657 W/°C…
Q: 2. Use superposition to find i in the circuit shown in Fig. 14-21. 2 mH 4√2 sin 1000 A 40 Fig. 14-21…
A: This question belongs to circuit theory . It is based on the concept of super position theorem .…
Q: Rated Torque (%) 300 250 200 150 100 50 T D с A B Motor Design Classes (NEMA) 20 40 60 Rated Speed…
A: Motor used for cooling Application : For cooling Application, there is a need for heat exchange…
Q: Consider an aperiodic continuous-time signal x(t) having the corresponding Fourier transform X(jw).…
A:
Q: Define the unit step function and the shifted unit step function. Need correct solution within 20…
A:
Q: Given the following unit step response of a second order system, calculate the following values: 1.…
A: The above plot is the standard plot of tep response of a 2nd order system. Peak time is defined as…
Q: Ohms law (CLO 1): The value of It in the following circuit equals:
A:
Q: Determine the Thevenin equivalent of the circuit in Fig. 10.27 as seen from the terminals a-b.…
A: The thevenin's equivalent circuit can be calculated by using the nodal analysis and the equivalent…
Q: 5. Which of the following technology was used by Intel to design its first 8-bit microprocessor?
A: The correct option along with the explanation is provided in the following section.
Q: H.W Q1) A four pole, three-phase synchronous generator is rated 250 MVA, its term is 24 kV, the…
A: Armature winding leakage reactance and a reactance used to depict armature reaction are combined to…
Q: System has the characteristic equation: The range of K for a stable system is: O a. O b. O C. Q(s) =…
A: In this question, We need to calculate the range of K for the stable system. We are solving this…
Q: A Carrier of 450 W,1MHz is amplitude modulated by sinusoidal signal of 15 KHz to a depth of 50%.…
A: Given: In an Amplitude modulation PC=450 WAC=1 MHzfm=15 kHzμ=50%=0.5
Q: Derive the transfer function of the * :circuit shown in Figure below Vin L C: Vout
A: Given data, Given circuit diagram is,
Q: (b) Figure Q.1b() shows a feedback system of unit step response of the system in Figure Q.1bii).…
A: Given: Input signal is step signal and a step response has been given. Required: Values of…
Q: In the following circuit, what are the minimum and maximum voltage values for Vout? MM 12 + elect…
A: Given circuit,
Q: The output resistance (Ro) for the following amplifier is Rsig 100ΚΩ G Vo RL • 200 ΚΩ 5kQ10kn 150 ΚΩ…
A:
Q: Use Thévenin's theorem to find Vo in the network in the figure below. Break the network at the 5 k…
A:
Q: A. B. Obtain the convolution of the following signals using z-transform: x² (n) = (i)* u(n − 1),…
A: Given here discrete signal and asked to find the convolution using the z-transform. we know Zanun…
Q: QUESTION 16 KVL (CLO 3): The value of Vx, in the following electric circuit equals: ww 72 15V -3 V…
A: Given data, Circuit diagram is given,
Q: Question-1 Consider the signal below: Given that A = 5 and B = 2 x(t) 0 2B B A t a) [ Write the…
A: Given A=5 B=2 Find Equation of the periodic waveform Express the periodic waveform in Fourier…
Q: Question Not yet answered 2 In the following circuit, what are the equivalent resistances seen by…
A: Given circuit:
Q: Draw the logic diagram of a four-bit binary ripple countdown counter using:1. flip-flops that…
A: Four-bit binary ripple countdown counter:- The 4-bit binary ripple counter in this circuit. The…
Q: In the given circuit below,
A:
Q: The power dissipated by a 10-ohm load resistor with a current rating of 5 amperes is if supplied…
A: Given, Resistance, R=10 Ω Current rating, Irated=5 A Supply, Vs=20 V
Q: If there are 10A of direct current through the filament of a light bulb, how many coulombs have…
A:
Q: When resistors R1 and R2 are connected in parallel each resistor dissipate 100 w and 75 w,…
A:
Q: How much demand factor is considered in the first 3000VA of hospital occupancy? 40% 35% 100% 20%
A: Demand factor:- It is defined as the ratio of maximum demand to the connected load on the system. It…
Q: Coupling capacitors Cc₁ and Cc2 provide AC coupling during the biasing of the transistor Vi Rin Ccl…
A: We know that At low frequency, capacitor acts as a open circuit i,e for dc signal capacitor acts as…
Q: (a) A unity feedback control system in Figure Q2a has an open loop transfer function of Gis) Rea 5…
A: Since you have posted the questions with multiple subpart so we are supposed to answer 3 subpart.
Q: 1. A three-phase induction motor delivers 100 hp while operating at an 80 percent efficiency and a…
A:
Q: The switch in figure has been open for a long time. It is closed at t = 0 s. What is the current…
A:
Q: Draw the waveform generated by the statements below:initial fork w = 0; #10 w = 1; # 40 w = 0; # 20…
A: It is given that: initial forkw = 0; #10 w = 1; # 40 w = 0; # 20 w = 1; #15 w = 0;join
Q: four-input EX-OR logic functions with the help of two-input EX-OR gates? Draw its logic
A:
Q: POSSIBLE QUESTIONS 1. How much energy in jouls is read. to move a a potential differ ol 6x2 CU…
A: NOTE_ “Since you have asked multiple questions, we will solve the first question for you. If you…
Q: If a voltage of 20 V is applied to the coil of a relay with 50 turns and internal resistance of 1 n,…
A: Given data, Number of turns N=50 turns Voltage V=20 V Resistance R=1 ohm
Q: Q6. For the system shown in Figure(5) R(s) K s(s+ 1) (s + 6) (s+4) K C(s) Figure (5) a) The value of…
A:
Q: Find out the Laplace transform of the shifted unit step function ult-a). Use the properties of…
A: In this case, the Laplace transform of the shifted unit step function is to be determined.
Q: Determine the Norton equivalent of the circuit in Fig. 10.30 as seen from terminals a-b. Use the…
A:
Q: - What is the configuration of this mplifier? [ - Draw the DC equivalent circuit for the mplifier […
A: The small signal input is applied to the gate of the MOSFET and output is taken at the drian. Hence…
Q: a) [ find the signal X₁(e). Given ₁ [n] = () 2u[n - 3],use DTFT to
A:
Q: Consider the following signal X(ew) X(ejw) = 1 1-e-j(w-2) 3e-j6w 1-e-jw + a) Find x[n], show all…
A:
Step by step
Solved in 2 steps with 1 images
- Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degreesShown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…Two lossy capacitors with Equal capacitance values and power factors of 0.01 and 0.02 are in parallel, and the combination is supplied from a sinusoidal voltage source. The power factor of the combination is ?
- Explain the following 1. Diffrence between DC and AC Electricity. 2. how to convert rectangular form to polar form and polar form to rectangular form. 3. why need to improve a power factorwhat is the reactive power absorbed by the load ZL in VAR? Assume source is in rmsA series RC circuit with R=4k ohms and C= 0.40 mF is connected to an AC voltage source e(t)= 100 sin200t. Determine the following: a). The overall power factor ( indicate big leading or lagging) b). The voltage drop across the resistor and the capacitor
- The below figure shows the waveform of the voltage and current in a purely inductive AC circuit. Voltage Current Using the voltage phasor as the reference, the current phasor Lags by 90° Is in phase with the voltage Leads by 90° Lags and then leads by 160°Problem Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V dc voltage source.If the phasor current is 45 degrees ahead of the phasor voltage, write down all the possibilities about circuit impedance.
- PHASE RELATIONSHIP SINUSOIDAL( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).The capacitive reactance (XC).... be affected by the harmonics of non- * .sinusoidal wave will all-of-them O could O cannot OC. Draw a general sine wave V vs t and I vs t plot for a purely resistive and a purely inductive circuit and show leading lagging parameters and clearly mark the phase difference.