Determine the PV array configuration (NpxNs) to charge a 48 V battery bank using a PWM (non-MPPT) charge controller with rated charging current = 30 A & maximum PV input voltage = 120 V. The datasheet of the PV module gives: Pmp = 355 Wp, Vmp = 38.68V, Imp = 9.17A, Voc = 46.88 V & Isc = 9.85 A all @STC. Note: Np represents the number of parallel-connected strings and Ns represents the string length. O a. 3x2

Determine the PV array configuration (NpxNs) to charge a 48 V battery bank using a PWM (non-MPPT) charge controller with rated charging current = 30 A & maximum PV input voltage = 120 V. The datasheet of the PV module gives: Pmp = 355 Wp, Vmp = 38.68V, Imp = 9.17A, Voc = 46.88 V & Isc = 9.85 A all @STC. Note: Np represents the number of parallel-connected strings and Ns represents the string length. O a. 3x2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The maximum power point of a solar cell occurs: O a. at both Isc and Voc Ob. at Isc O c. none of these Od. at Voc
1. For a certain D-MOSFET, IDSS = 18 mA, and VGS = +10V. Vp =4V. a) Determine ID at VGS =+ 3V. b) Determine ID at VGS = -3V. %3D
• In MOSFET, it is the foundation upon which the device will be constructed and is formed from a silicon base A. Substrate, B. Slab, C. Source, D. Base.
Bypass diodes are connected in parallel with a solar cell to prevent the discharge of current from the battery to cell during night event. True False
How do we know current flows in source terminal? Is this common for n-type mosfet? What is an n-type mosfet?
Q) Draw and explain the charging time characteristics of first order RC circuit?
Set up a midpoint bias for a JFET with IDSS = 14 mA and VGS(off) = -10 V. Use a 24 V dc source as the supply voltage. Show the circuit and resistor values. Indicate the value of ID. Indicate the value of VGS. Indicate the value of VDS.
(b) Draw the ID - VD curves for this MOSFET for ±VD for V₁ = 0 and V₁ = 1 V. VȚ = 1V. n V₁ + p-type D ID V₁
In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.48 V respectively. The form factor of this circuit is ___________________.
Subject:Electronics Engineering How MOSFET has been constructed? Explain the principle of operation of MOSFET at different values of VGS and VDS
Vcc=15V Q1: BC237 Rc 3.6kQ or BC238 B=200 VBE(on)=0.7V R1 110KQ Rs Cci 1000 4.7µF Cco 4.7µF R2 ·27kΩ RE 1.2kQ RL 12kΩ Vs Rin Rout Figure 1. Common-emitter amplifier. 2)
Estimate the output voltage of a 80W,PV module when it is short circuited? a. 0V b. equal to its Voc value c. less than its Voc value d. more than its Voc value Clear my choice