Determine the mass flow rate of a steam turbine if the inlet conditions are as follow T= 400 C and P = 3000 %3D %3D kPa. The fluid leaves the turbine at 70 kPa and 160 C. The output power of turbine is equal to 1200000 W. O a. 2.8 kg/s O b. 9.32 kg/h O. 12.74 kg/s O d. 10.9 kg/h

Determine the mass flow rate of a steam turbine if the inlet conditions are as follow T= 400 C and P = 3000 %3D %3D kPa. The fluid leaves the turbine at 70 kPa and 160 C. The output power of turbine is equal to 1200000 W. O a. 2.8 kg/s O b. 9.32 kg/h O. 12.74 kg/s O d. 10.9 kg/h

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Related questions

Q: Consider a regenerative gas-turbine power plant with two stages of compression and two stages of…

A: The given data and the t-s diagram is shown in the following attached image:

Q: It is suggested to pump 5,000 kg/h of a liquid at 114°C and 1.1 atm abs pressure from a reboiler of…

Q: In an air standard gas turbine cycle, air at 14.5 psia and 70 F is first compressed to 80 psia in a…

Q: A turboprop engine consists of a diffuser, compressor, combustor, turbine, and nozzle. The turbine…

Q: The following performance data were generated by a gas turbine having intercooling: LP compressor…

A: .

Q: Air enters the compressor of a gas-turbine engine at 300 K and 100 kPa, where it is compressed to…

Q: Compare the thermal efficiency of a two-stage gas turbine with regeneration, reheating, and…

A: Given data: P-V diagram of a typical Gas turbine cycle with all the modification will be given as:…

Q: Consider a regenerative gas-turbine power plant with two stages of compression and two stages of…

Q: Air enters a gas turbine at P1=1100 kPa and T1= 860 K and leaves the turbine at P2=100 kPa and T2=…

A: Assumption:- Air is an ideal gas, so we are taking specific heat of an ideal gas. And the given…

Q: es and volume flow rate listed in the figure. Do NOT assume constant specific heats. If the…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Time left 9:22:38 Air enters a compressor with h = 378.7 kJ/kg and exists with h₂ = 7134 kg Steam…

Q: Question attached

A: Saturation Pressure: The pressure exerted by the vapour on the liquid when both liquid and vapour…

Q: A power cycle produces 12 MW by partial conversion of the received heat as a result of steam…

A: Given Data Heat produce is :Q˙c=12 MW Saturated pressure is :Psat=1900 kPa Temperature of sink is:…

Q: For the binary cycle shown, the enthalpies are h1 = 3,195 kJ/kg; h2 = 2,265 kJ/kg; h3 = 178 kJ/kg;…

Q: A R-12 compressor operates betwwen eveoperating temperature of 4 c ( hg = 353 kj/kg ), vg = 0.04895)…

Q: A two-stage compressor with an ideal intercooler receives 0.4 m°/s of air at 100 kPa and 310°K. If…

A: Given Pressure, P1 = 100 kPa P2 = 707.1 kPa Temperature, T1 = 310 K Find…

Q: at a stage in a reaction turbine, the mean blade ring diameter is 1 m. the turbine runs at 3000 rpm.…

A: Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Q: Steam enters a turbine with an enthalpy of 3300 KJ/kg and leaves with an enthalpy of 2400 kJ/kg. The…

A: Given datahi=3300kJ/kgho=2400 kJ/kgP=6MWv1=60m/sv2=200m/sz1=12mz2=5m ***As the Missing term is mass…

Q: Determine the flow rate required to produce 25 MW of shaft power from a steam turbine in which the…

Q: An air compressor with a clearance of 4% compresses 14.73 cubic meter/min of air from 97 kpa, 27°C…

A: Given Data The initial temperature is: T1=27°C=300 K The clearance is: C=0.04 The initial pressure…

Q: Helium expands polytropically steadily through a turbine according to the process pv3=C. The inlet…

A: To find out the exit temperature Apply ideal gas equation for the polytropic process…

Q: 9. The effluent from a gas compressor is cooled by contacting with water in a heat exchanger. The…

A: Heat exchangers are of two types that is counter flow and parallel flow type heat exchanger . The…

Q: (5) Asingle-acting, twin-cylinder 15.25 x 15.25-cm. compressor receives saturated ammonia vapor at…

Q: A 36 cm x 36 cm , horizontal double acting air compressor w/ 5% clearance operates at 120 RPM and…

Q: A gas enters a turbine at an inlet state of 800 kPa. The gas expands and leaves the turbine at an…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: H.W: - Steam at 15bar & 330°C expand isentropically in a turbine to 0.12 bar if the flow rate of…

Q: Steam at 3.5 MPa and 400°C enters an adiabatic turbine with a volume flow rate of 5 m /s. An…

A: Given: P1=3.5MPa & T1=400°C Q=5m3/s P2=500KPa & T2=250°C P3=100kPa

Q: An adiabatic steam turbine receives steam from two boilers. One flow has a mass flow rate (m) of 4.7…

Q: Consider a regenerative gas-turbine power plant with two stages of compression and two stages of…

Q: In a gas turbine plant operating on the constant-pressure cycle, the pressure ratio is 6 and the…

A: Given Data Tmax=1088 K Tmin=272 K

Q: 1. Determine the mass flow rate of a Makban power plant operating a superheat vapor entering the…

A: We will answer the first question since the exact one was not specified. Please submit a new…

Q: 3. Steam enters the turbine at the rate of 1.5 kg/s with enthalpy of 2300 kJ/kg and exhaust enthalpy…

A: Find the turbine work in HP.

Q: A steam power plant develops a power output of 2840Kw. Te enthalpy of steam at the inlet if 2500…

A: Given data, W= 2840 kW h1= 2500 kj/kg x=0.8, hf2=561 KJ/kg hfg2=1832 K/kg.

Q: Determine the efficiency of the reversible Heat Engine cycle shown: 4 800K 600K 300K 1 S (kJ/kg-K)…

A: This is the very basic question of thermodynamics. Used concept is area under the T-s curve On…

Q: JA steam power plant employs two adiabatic turbines in series. Steam enters the firs turbine at…

Q: A combined gas turbine and steam power cycle is shown in the schematic below. Air enters the…

A: Given, ms˙=15 kg/smw˙=150 kg/s

Q: Steam expands from 9.0 MPa and 4500C to saturated vapor @75 kPa through an adiabatic turbine. If the…

A: Answer: ◆ The power generated by the turbine is 11.9 MW. ◆ Therefore, the correct answer is option…

Q: In a steam power plant, steam enters the turbine at 2.5 MPa and 500 C. The condenser pressure is 15…

Q: Q 5) A turbine, operating under steady-flow conditions, receives (4500 kg) of steam per hour. The…

Q: (5)A steam power plant operates on the cycle shown in the figure. If the isentropic efficiency of…

A: Given: The isentropic efficiency of turbine, ηt = 87% The isentropic efficiency of pump, ηp = 85%…

Q: Water enters a turbine pump at 30kPa (vf= 0.0010223 cu. m per kg) and discharges at 2.8 MPa. The…

Q: Air enters a multistage compressor of a jet engine at 0.65 atm and 275 K with a flow rate of 63.5…

Q: Refrigerant-12 enters the condenser of a vapor-compression refrigera- tion system at 175 psia and…

Q: - The temperature of the water vapor at the entrance to a turbine is 400ºC and the pressure is…

A: Option E is the correct. Turbine power=22.28 MW

Q: In a reaction turbine, the drum diameter is 2.15 m, speed of turbine is 750 rev/min and the steam…

A: Given data, Drum Dia (d) - 2.15 m Speed of turbine (N) - 750 RPM Steam Flow (m) - 14.2 kg/sec Blade…

Q: At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a…

A: Here we need to construct the velocity traingle taking ϕ,α = Exist angle = 20 θ,β= inlet angle =…

Q: An adiabatic steam turbine receives steam from two boilers. One flow has a mass flow rate (m) of 5.7…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Determine the mass flow rate of a steam turbine if the inlet conditions are as follow T = 400 C and P = 3000
%3D
%3D
kPa. The fluid leaves the turbine at 70 kPa and 160 C. The output power of turbine is equal to 1200000 W.
O a. 2.8 kg/s
O b. 9.32 kg/h
O. 12.74 kg/s
O d. 10.9 kg/h

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

8. A turbine passes 67.5 kg/h of steam at 200 km/h at 8 MPa and leaves at 0.5 MPa as wet steam with a speed of 90 km/h and a specific volume of 0.189 m3/kg. d. What must be the steam input conditions (T,H) to turn on a device that consumes 30 kW? and. What is the mass and volumetric flow rate of the water at the outlet? F. What is the input and output area?
Pls answer thank you! Steam enters the turbine at the rate of 2.5 kg/s with enthalpy of 3200 kj/kg and exhaust enthalpy of 1100 kj/kg . Steam is extracted from the turbine at the rate of 1 kg/s for heating purposes with enthalpy of 2750 kj/kg. What is the turbine work in KW.
Q1 / A: Derive the steaay flow energy equation and reduce it for: a. A turbine ( Reversible Process) b. A pump ( Reversible Process) c. A nozzle ( Reversible Process) d. A throttling ( Irreversible Process) Assume that the working fluid is an ideal gas and the entrance and exit are at the same level. B- For a reversible adiabatic process prove the equation pvr = constant can apply for the relation between pressure and specific volume for a perfect gas. %3D
There are two turbine stages with a reheater in between, as shown below and the following conditions are provided. Assume the mass flow rate of air = 1 Kg/s. Turbine stage 1 Stream 1 2 3 4 Reheat combustor P (kPa) T (K) 1200 350 350 100 1200 1200 3 Turbine stage 2 h (kJ/kg) W cycle • Determine the total work developed, which is the sum of the work developed by the first stage and the work developed in the second stage. • Determine the heat added in the reheater. • If the reheat is turned off, streams 2 and 3 no longer exist and we go directly from 1 to a new state at stream 4. What is h4 and what is the work generated in the turbine in this case?
Pls. Answer this..? A steam engine has 10% brake thermal efficiency and consumes 750 kg/hr steam. The enthalpy of steam at the entrance ang exit of the engine and condenser are 2800 and 450 kj/kg repectively. Determine the brake power of the engine in kw.
IN A THROTTLING VALVE, steam of P = 1000 kPa H = 1000kJ/kg flows until P becomes 100kPa. What is the fraction of the liquid that was vaporized? a.0.118 b.0.189 c.0.159 d.0.140 e.0.258
Ans. 3908 m/min. 14.5 Find the cylinder dimensions of a single-cylinder, double-acting compressor handling 28.32 e/revolution of air from 99.975 kPaa to 723.954 kPaa. Compression and reexpansion are in accordance with PV135 = C. Use the conventional volumetric efficiency; c = 5% and L/D = 1. %3D %3D
Determine the mass flow rate of a steam turbine if the inlet conditions are as follow T = 400 C and P = 3000 kPa. The fluid leaves the turbine at 70 kPa and 160 C. The output power of turbine is equal to 1200000 W. O a. 2.8 kg/s O b. 9.32 kg/h C. 12.74 kg/s O d. 10.9 kg/h
Q4: Why the stroke length of the racing cars' engines is always smaller than its bore diameter?
5.0 A 140 x 140-mm, twin-cylinder, single acting refrigerant- 12 compressor running at 600 rpm carries a refrigeration capacity of 40 kW while operating at 350 kPa suction and 1300 kPa discharge pressures. , Assuming the same load to be carried with the same volumetric efficiency and if the discharge pressure shall be raised to 1400 kPa, a) what is the percent increase in mass of R-12 (b)What will be the new volumetric displacement of the compressor the compressor be run? in m/sec ?;(c)At what speed should
f. A water-jacketed compressor receives 140 L/s air at 100 kPa and 21 deg C and discharges the air at 140 deg C. Cooling water entering at 16 deg C and leaving at 21 deg C is circulated at the rate of 0.18 L/s. Determine the power required for the driving motor for this compressor, assuming the friction losses with rotating parts account to 5% of the total power required. a. 10 kW b. 15 kW c. 20 kW d. 25 kW
d.a) A single-cylinder reciprocating compressor has a 5% clearance and a bore and stroke of 25 cm x 30 cm, respectively. The compressor operates at 500 RPM. The air enters the cylinder at 27 C and 95 kPa and discharges at 2000 kPa. Ambient air conditions are 101.3 kPa and 27C. If the polytropic exponent n = 1.3 for compression and re-expansion processes, determine the volume of the actual air being delivered by the compressor in m3/hr. a. 233.66 m3/hr b. 323.66 m3/hr c. 212.66 m3/hr d. 263.66 m3/hr For number 2a, the power required to drive the unit, in kW, if the compressor efficiency is 82%. a. -84.62 kW b. -52.62 kW c. -62.84 kW d. -74.84 kW