A step up chopper has input voltage 110 V and output voltage 150 V. The value of duty cycle is.
Q: What are the resolution and the quantization error of a 20 bit A/D convertor with a range of -10 to…
A: We need to find out resolution and quantization error for given ADC .
Q: The following test data were obtained for a three-phase, 220 V, 5 HP motor operating at full load:…
A:
Q: The three windings of a three phase, 60 Hz AC generator are connected in wye. Each of the three coil…
A: In this question, We need to determine the line voltage, line current and total rating of the three…
Q: is In a BJT, Ico = Icgo = 2 μΑ . Given a = 0.99 , the value of Iceo A 2 μ.Α Β 99 μ.Α c 198 μ.Α D 200…
A: Given- BJT- ICO=ICBO=2μA,α=0.99, To Find- The value of ICEO,
Q: A three-phase, four-wire, wye-connected system supplies a noninductive lighting load only. The…
A:
Q: A 220 V, 60 Hz, 6-pole, 3-phase induction motor has a slip of 3%. Determine the slip speed, and the…
A: Given, In a 3-phase 220 V induction motor, Number of poles, P=6. Frequency, f=60 Hz. Slip,…
Q: 33. What is the name given to radio signals in the high-frequency range?
A: Note: We’ll answer the first question since the exact one wasn’t specified. Please submit a new…
Q: What are the resolution and the quantization error of a 20 bit A/D convertor with a range of -10 to…
A: Given, An AD converter has, Number of bits, n=20. Voltage range is from -10 V to 10 V.
Q: 26. What does a radio wave consist of? Answer:
A: Since you have asked multiple question, we will solve the first question for you. If you want any…
Q: The AND gate serves the same purpose in this circuit when employed as a modulator. A demodulator…
A:
Q: 12010° Ꮩ V 12£1 Lossless, v2c/3 Za = 50 80 m 80 £2
A:
Q: What is a straight-line or linear accelerator?
A: Given: What is a straight-line or linear accelerator?
Q: 2. A 6-pole 5 kW, 50-Hz, 3-phase induction motor having a full load slip of 3%, what will be the…
A: Given: A 3-phase induction motor has, Number of poles, P=6. Rated power, P0=5 kW. Frequency, f=50…
Q: Three resistors of 10, 15 and 20 ohms each are connected in parallel. What is the equivalent…
A: The equivalent resistance can be calculated by using the parallel resistance reduction technique.
Q: 5.115 The propagation constant of a transmission line is 0.15 x 10-3+j1.5 x 10-3. The wavelength of…
A: Given, Propagation constant, γ =0.15 ×10-3 + j 1.5 ×10-3 Also, γ =α+jβ where β is the phase constant
Q: 2. Compute the kinetic energy of an 1800 lb automobile traveling at 30 mi/hr, How many times as…
A: We need to tell about kinetic energy .
Q: What is the Norton equivalent current In between a and b for the circuit shown in Figure 4.25? 's 4…
A: We need to find out the Norton current for given by using the nodal analysis .
Q: What is the size in square millimeter is the cable of 250 MCM size
A: Here, For the cable of 250 MCM size, we have to determine the size in square millimeter.
Q: Three capacitors of 21, 10 and 17 microfarads respectively are connected in series across a 108-V…
A:
Q: R₁ R₁ + R, Q3: Derive V-Vx- Rx in the circuit shown in Fig(1).
A: Given, The circuit is,
Q: Schedule: e. Toggle the T input with J = K = 1 4.) To preset the a JK flip-flop to the binary 1…
A:
Q: 1. Normally the duration of pulses applied to the set or reset input should only be long enough to…
A: Note: We are authorized to answer the first three sub-parts at a time, so we are answering the first…
Q: a www R, = 1Ω ε = 12V b C www R₂ = 29 2Ω e g d_R₂ = 3N_ƒ Use Kirchhoff's Law to solve for the…
A:
Q: Convert the expression below to: (You may use extra sheet of paper for your solution) A. NOR B. NAND…
A: This is a problem of logic gate function. The solution is given in the next step.
Q: In the circuit shown in Figure 2.33, what is the voltage Vo? O 2.5 mA Figure 2.33 O a. V₁ = 3 V O b.…
A:
Q: A 250V, 30Hz generator supplies power to a parallel circuit consisting of a 20Hp motor whose…
A: Given: Supply generator with V=250Vf=30Hz Load-1, Motor of 20HP, Efficiency, η=90% Power factor=0.8…
Q: Using Gauss’ law deduce the expression for the electric field due to a uniformly charged spherical…
A: Electric Field:- Each point in space has an electric characteristic whenever a charge of any kind is…
Q: Q13) Calculate the current I, in the following circuit 100mA I + Vs R 177/ 1 50mA 2 TZ I 3 D
A: Given data, Circuit diagram is given as,
Q: Q3) Using the superposition theorem, find the current, voltage and the power dissipated through R₁…
A:
Q: In the circuit shown in Figure 3.25, what is the mesh current I3? 8V R₂ 1 ΚΩ R₁ 2 ΚΩ R₂ 1.5 kg!…
A:
Q: through R₁ for the network of Fig.3. R₁ Zon R₁30 12 6 A IR₂ E₁12 V Fig. 3 R₁12 81 E₂-8V
A: here superposition theorom has been applied. KCL is also used to solve it using superposition…
Q: How much energy does a 11 V battery have when it stores 6 coulombs of charge?
A:
Q: Give at least 3 Advantages of Reheat Regenerative Cycle in Thermal Power Plant
A: Intoduction - Reheating is a method used to improve the thermal efficiency of gas and steam turbine…
Q: 2. Determine the voltage e, across the 20-12 resistor. 15 V 4011 www 150 www 2002
A: Voltage division rule for resistor in series Total R = R1 +R2 +.....+Rn any resistor Ri Ω is VRi =…
Q: Consider the following circuit (See image): Show that it is a unity gain absolute value circuit,…
A:
Q: A transformer operating at 0.7 lagging power factor has an efficiency of 95%. HV winding: delta…
A:
Q: the voltage gain of an amplifier is 250 while the current gain is 100. Compute for the power gain in…
A: Given: For an amplifier, The voltage gain is, Av=250. Current gain, AI=100.
Q: Q1) Find the Thevenin equivalent circuit for the network in the shaded area of Fig. 1. Then, find…
A:
Q: 00 01 03 0.3 Given the characteristic equation of the denominator as: What is damping ratio of the…
A: Given, The transfer function, Gs=25s2+3s+25.
Q: Calculate the base transport factor. Assume transistor parameters of xB=0.80 µm and LB=10.0 μm
A: We need to determine the base transport factor. If transistor parameters of xB=0.80 µm and LB=10.0…
Q: If an amplifier has a voltage gain of 40 dB, and an input signal of 22 mV, the output signal voltage…
A: Given: Amplifier voltage gain, Avdb=40 dB. Input voltage, Vin=22 mV. Output voltage, Vout=?
Q: Calculate the body-effect coefficient and the change in the threshold voltage due to an applied…
A: Calculation of the body-effect coefficient and the change in the threshold voltage due to an applied…
Q: For the system in the given figure the characteristic equation is R(S) K(s+1) S + 3 s(s+2) C(s)
A: Solution !!
Q: What is the Thévenin equivalent resistance Rth across a and b for the circuit shown in Figure 4.20?…
A:
Q: r=7m contains a uniform charge density , in C/m³. Use Gauss law Q4: The volume in spherical…
A: We need to find out D and E for given charge distribution by using of gauss law .
Q: A technique is set at 90 mA and 600 ms and produces an intensity of 300 mR If the technician…
A: Given,First case - Current, I1 = 90mATime, t1=600 msIntensity, R1=300 mRSecond case - Current, I2 =…
Q: A series RLC circuit is connected to an AC source that provides a current of I(t) = I,cos(wt). What…
A: In a series RLC circuit, resistor, inductor and capacitor are connected in series with the source.…
Q: For a LTI system, drive the frequency response, if you know that the input is: r(t) = M cos(ωt + θ)
A: Given: The input, r(t)=Mcosωt+θ
Q: 부 30 VI 82 2 68 2 40 Vi 47 2 100 22 Figure 9-2 Given the circuit in Figure 9-2. find the approximate…
A: Given circuit,
Q: In the circuit shown in Figure 3.28, what is the mesh current I₁? 10 V R₁ 1 ΚΩ Figure 3.28 O a. l₁ =…
A:
A step up chopper has input voltage 110 V and output voltage 150 V. The value of duty cycle is.
Step by step
Solved in 2 steps
- Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 RL out OV 10 kN IN4001 alllA single phase full converter feeds power to RLE load with R=10 ohm, L=10 mH and E=50 V, the ac source voltage is 230 V, 50 Hz. For continuous conduction, what is the average value of load current for firing angle delay of 600 ?The three phase converter with an ac side inductance L2 25 uh and VLL equal to
- An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?A chopper circuit works at a frequency of 4 kHz of a 220 V dc supply. For 180 V output voltage, find the conduction and blocking periods of a thyristor in each cycle. Select one: a. 0.209 ms, 0.234 ms b. 0.404 ms, 0.055 ms c. 0.204 ms, 0.045 ms d. 0.704 ms, 0.897 msQ5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
- Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R1 V out 10 kN D2 IN4001 allleDoes the input power factor of convertors depend on the load power factor? why?Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle
- In the given circuit, a step down transformer with an RMS voltage as 110V /11-0-11 V is used with RL = 1 KO. Assume diode as Germanium and the input frequency is F= 50HZ. D, CT Vin RL D2 1- Name the given circuit. 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms. allDesign a bridge-type full-wave rectifier fed from the 240-V line through a step-down transformer. The load requires an average voltage of 14 V and average power of 6 W.A buck converter, as shown in Figure (a) below, is working in steady state. The output voltage and the inductor current can be assumed to be ripple free. Figure (b) shows the inductor voltage Vi during a complete switching interval. Assuming all devices are ideal, the duty cycle of the buck converter is M VA 30 V- DA R TON TOFF (a) -20 V- (b)