A hydraulic lift is used to jack a 960-kg car 42 cm off the floor. The diameter of the output piston is 18 cm, and the input force is 380 N. (a) What is the area of the input piston? (b) What is the work done in lifting the car 42 cm? (c) If the input piston moves 13 cm in each stroke, how high does the car move up for each stroke? (d) How many strokes are required to jack the car up 42 cm? (e) Show that energy is conserved.

A hydraulic lift is used to jack a 960-kg car 42 cm off the floor. The diameter of the output piston is 18 cm, and the input force is 380 N. (a) What is the area of the input piston? (b) What is the work done in lifting the car 42 cm? (c) If the input piston moves 13 cm in each stroke, how high does the car move up for each stroke? (d) How many strokes are required to jack the car up 42 cm? (e) Show that energy is conserved.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Manny Pacquiao owns a hydraulic press for his training to box in the presidential race. It is filled with an hydraulic oil with relative density of 0.82. Can you draw the FBD of the mechanism and compute the actuating force needed to counteract the 10kN punch weight?
A rectangular tank 20 ft long by 6 ft deep by 7 ft wide contains 3 ft of water. If the linear acceleration horinzontally in the direction of the tank's length is 8.05 ft/sec2, a.) Compute the total force due to the water acting on each end of the tank and b.) show the difference between these forces equals the unbalanced force necessary to accelerate the liquid mass. i need an answer right away please sir , thanks.
An open horizontal tank 3 m high, 3.5 m wide and 6 m long is initially filled at 2 m of water. a. Determine the required acceleration in m/s² so that no water will be spilled? 3.270 Determine the required acceleration m/s? so that 1/3 of the initial volume of water will be spilled. b. [ Select ] c. Determine the remaining volume in cu.m. if it accelerated at 7 m/s^2. [ Select ] Determine the minimum hydrosatic force in kN at the side of the tank if 2/3 of the initial volume will be spilled. d. [ Select ] Determine the maximum hydrosatic force in kN at the side of the tank if it accelerates at 3 m/s^2. е. [ Select ]
Determine the load that can be lifted by the system shown if R2 is increased to 25 cm.
A hydraulic device is used to raise an 89-kN truck. If oil sp gr 0.810, acts on the piston under a pressure of 1.22 MPa, what a diameter is required?
) A 5-gal, cylindrical open container with a bottom area of 120 in²is filled with water and rests on the floor of an elevator. If cylindricalcontainer is accelerated upward at 3 ft/s², what resultant force doesthe container exert on the floor of the elevator during thisacceleration? The weight of the container is negligible. (Note: 1 gal= 231 in³)
A flat plate of area 1.5 x 10° mm? is pulled with a speed of 0.4 m/s relative to another plate located at a distance of 0.15 mm from it. Find the force and power required to maintain this speed, if the fluid separating them is having viscosity as 1 poise.
Problem 5 Gasoline having a specific gravity of 0.8 is flowing in the pipe shown at a rate of 5 ft³/s. What is the pressure at section 2 when the pressure at section 1 is 18 psig and the head loss is 9 ft between the two sections? Assume α = 1.0 at all locations. Vertical A₁ = 0.80 ft² 12 ft 4₂ = 10.20 ft²
Two concrete blocks weighing 1423 N each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown? Figure P 7.38 -254 mm 457 mm 4y = 0,5 Plastic liner 457 mm H=L0- 5604 N/m
Q8) You are designing a system for moving aluminum cylinders from the ground to a loading dock. You use a sturdy wooden ramp that is 2.00 m long and inclined at 37.0 degrees above the horizontal. Each cylinder is fitted with a light, frictionless yoke through its center, and a light (but strong) rope is attached to the yoke. Each cylinder is uniform and has mass 420 kg and radius 0.300 m. The cylinders are pulled up the ramp by applying a constant force F to the free end of the rope. F* is parallel to the surface of the ramp and exerts no torque on the cylinder. The coefficient of static friction between the ramp surface and the cylinder is 0.120. a) What is the largest magnitude F° can have so that the cylinder still rolls without slipping as it moves up the ramp? b) If the cylinder starts from rest at the bottom of the ramp and rolls without slipping as it moves up the ramp, what is the shortest time it can take the cylinder to reach the top of the ramp?
10 cm 3cm 3cm 2em 2cm 40 cm Center f wheel + ass of rotation 1. An 80 cm diameter metal wheel has the cross-section shown. Determine the surface area of the wheel Determine the volume of the wheel
Problem 4: Inputs: ● ● B C Weight of person = 165 lb μ = 0.4 0 = 60° W A System 1 B C W a) Max weight that can be lifted in system 1 b) Max weight that can be lifted in system 2 System 2 Close-up view of pulley system In each scenario, you must determine the maximum weight, w, that can be lifted before the man slips. The problem starts out as a pulley problem, but thereafter it is a friction problem. (Thought you were done with that right?)