3. The functions of the control system is monitored by the 8-bit length microcontroller which has in-built digital to analog converter. The controller behaves as fully open stage and output of the digital word 1111 1111, when a maximum voltage of 6 V is applied to the controller. i) calculate the change in voltage when there is a change in 1 bit in input, ii) Calculate the total analog output voltage for the input digital value 0000 0011.

3. The functions of the control system is monitored by the 8-bit length microcontroller which has in-built digital to analog converter. The controller behaves as fully open stage and output of the digital word 1111 1111, when a maximum voltage of 6 V is applied to the controller. i) calculate the change in voltage when there is a change in 1 bit in input, ii) Calculate the total analog output voltage for the input digital value 0000 0011.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 30RQ

See similar textbooks

Similar questions

3. The functions of the control system is monitored by the 8-bit length microcontroller which has in-built digital to analog converter. The controller behaves as fully open stage and output of the digital word 1111 1111, when a maximum voltage of 6 V is applied to the controller. i) calculate the change in voltage when there is a change in 1 bit in input, ii) Calculate the total analog output voltage for the input digital value 0000 0010.
i) Draw the electronic circuit of PI controller and also write the electronic output equation and General controller output equation . Mention advantages . ii) Suggest two sensing elements to measure Pressure parameter. iii) Identify the control strategy used in the given figure and define
6. The figure below shows the control system of a STATCOM. a) Explain the function of this controller. b) What does Vdc and VdeRef show? Why are they compared? c) What is the use of the phase lock loop? loRet Real and reactive current computer loq lop Error amplifier IPRef Error amplifier Magnitude and angle computer Vac Vachet Phase- locked loop 0+a Vo v;(V/0°) Gate pattern logic 000 000 Voi(V (T) La) Converter
Q2 Figure Q2 shows a Linear Feedback Shift Register circuit. Write down the VHDL entity associated with a 6-bit shift register with the inputs and outputs as shown in Figure Q2. (a) (b) Write down a VHDL architecture for a 6-bit shift register. 6-bit parallel out shift register clk d reset serial_in Figure Q2
Nuclear Instrumentation and Control A proportional controller has a proportional band value of 50%. What is its gain? The controller experiences a 2 volt change at its measurement input. After the controller returns the process to stable operation, what will the controller output voltage be?
6. The figure below shows the control system of a STATCOM. a) Explain the function of this controller. b) What does Vdc and VdeRef show? Why are they compared? c) What is the use of the phase lock loop? lore! Real and reactive current computer loa lop Error amplifier IPRef Error amplifier Magnitude and angle computer Vac Vachet Phase- locked loop 0+a Vo v;(V/0°) Gate pattern logic 000 000 Voi(V (T) La) Converter
Q 3-1: Pressure sensor rated at 0-500 psi and has an output of 0-10 Volts DC (10 V correspond to 500 psi) .it is connected to PLC analog input module that is 12 Bits if the PLC read the Analog input as 8B3 HEX ,what is the pressure in psi and the resolution in psi for the System.
Can you please help me design some instructions that ze ros the content of the accumulator register? Thanks will thumbs up
Comparing the performance with controlled rectifier circuit which one of the following statement is correct for DC -DC chopper ? O a. Regenerative braking process is very slow O b. Efficiency is poor in chopper circuit O c. small filters are required O d. Switching frequency is not responsible for output ripples
Gradual change in the measurement output while the measurand remains constant is called:Select one:a. Sensor reproducibleity b. Sensor offsetc.Sensor driftd. Sensor Hysteresis
30)Which of the following conditions is NOT considered when and a normally-open versus anormally-closed input instruction is selected? A)Matching the type of input contacts (NO or NC) with input instructions (NO or NC). B)The active state of the input field device: active or not active. C)The type of contacts (NO or NC) present on the input field device. D)The desired state of the output field device: active or not active.
Define FACTS and write it’s necessity and Benefits. With neat diagrams briefly describe different types of FACTS controllers. Describe SVC and STATCOM and compare their performance