103 Chemistry I Laboratory Manual, 2019 Revision Part 2: Determination of the Molarity of a Sulfuric Acid Solution strans Trial 1 Trial 2 Trial 3 Trial 4* Starting Buret Reading: |•74 L On15L 0-59L Ending Buret Reading: Il.83 L10-10L 10.591 mL of Titrant Used: 10.09L/9.95L10.00L mmole of NaOH: 1.009 moll 9.95 no 1.0 ml mmole of H2SO4 0.5 mal 5.0 0.5 5.Ond Molarity of H2SO4 Solution 0.OS M 0.5 M 0.OS M O.0SM Average Molarity 0.6M

103 Chemistry I Laboratory Manual, 2019 Revision Part 2: Determination of the Molarity of a Sulfuric Acid Solution strans Trial 1 Trial 2 Trial 3 Trial 4* Starting Buret Reading: |•74 L On15L 0-59L Ending Buret Reading: Il.83 L10-10L 10.591 mL of Titrant Used: 10.09L/9.95L10.00L mmole of NaOH: 1.009 moll 9.95 no 1.0 ml mmole of H2SO4 0.5 mal 5.0 0.5 5.Ond Molarity of H2SO4 Solution 0.OS M 0.5 M 0.OS M O.0SM Average Molarity 0.6M

Chemistry by OpenStax (2015-05-04)

1st Edition

ISBN:9781938168390

Author:Klaus Theopold, Richard H Langley, Paul Flowers, William R. Robinson, Mark Blaser

Publisher:Klaus Theopold, Richard H Langley, Paul Flowers, William R. Robinson, Mark Blaser

Chapter14: Acid-base Equilibria

Section: Chapter Questions

Problem 98E: Calculate the pH of a buffer solution prepared from 0.155 mol of phosphoric acid, 0.250 mole of...

See similar textbooks

Similar questions

What is an acidbase indicator? Define the equivalence (stoichiometric) point and the end point of a titration. Why should you choose an indicator so that the two points coincide? Do the pH values of the two points have to be within 0.01 pH unit of each other? Explain.
Sketch the titration curve for a weak acid titrated by a strong base. When performing calculations concerning weak acidstrong base titrations, the general two-slep procedure is to solve a stoichiometry problem first, then to solve an equilibrium problem to determine the pH. What reaction takes place in the stoichiometry part of the problem? What is assumed about this reaction? At the various points in your titration curve, list the major species present after the strong base (NaOH, for example) reacts to completion with the weak acid, HA. What equilibrium problem would you solve at the various points in your titration curve to calculate the pH? Why is pH 7.0 at the equivalence point of a weak acid-strong base titration? Does the pH at the halfway point to equivalence have to be less than 7.0? What does the pH at the halfway point equal? Compare and contrast the titration curves for a strong acidstrong base titration and a weak acidstrong base titration.
Which of the indicators in Fig. 14-8 could be used for the titrations in Exercises 61 and 63?
Malonic acid (HO2CCH2CO2H) is a diprotic acid. In the titration of malonic acid w ith NaOH, stoichiometric points occur at pH = 3.9 and 8.8. A 25.00-mL sample of malonic acid of unknown concentration is titrated with 0.0984 M NaOH, requiring 31.50 mL of the NaOH solution to reach the phenolphthalein end point. Calculate the concentration of the initial malonic acid solution. (Sec Exercise 113.)
A 10.00-g sample of the ionic compound NaA, where A is the anion of a weak acid, was dissolved in enough water to make 100.0 mL of solution and was then titrated with 0.100 M HCl. After 500.0 mL HCl was added, the pH was 5.00. The experimenter found that 1.00 L of 0.100 M HCl was required to reach the stoichiometric point of the titration. a. What is the molar mass of NaA? b. Calculate the pH of the solution at the stoichiometric point of the titration.
Determine the dominant acid-base equilibrium that results when each of the following pairs of solutions is mixed. Indicate the equilibrium by writing 1 for a strong acid, 3 for a weak acid, 4 for an acidic buffer, 7 for a neutral solution, 10 for a basic buffer, 11 for a weak base, and 13 for a strong base. (a) 10.0 mL of 0.15 M NaOH + 15.0 mL of 0.10 M HNO3 (b) 25.0 mL of 0.10 M HCl + 10.0 mL of 0.25 M NH3 (c) 50.0 mL of 0.050 M NaOH + 50.0 mL of 0.10 M NH3 (d) 50.0 mL of 0.10 M NH3 + 50.0 mL of 0.05 M HCl
A buffer is prepared in which the ratio [ H2PO4 ]/[ HPO42 ]is 3.0. (a) What is the pH of this buffer? (b) Enough strong acid is added to convert 15% of HPO42- to H2PO4-. What is the pH of the resulting solution? (c) Enough strong base is added to make the pH 7.00. What is the ratio of [H2PO4-] to [HPO42-] at this point?
A 0.400-M solution of ammonia was titrated with hydrochloric acid to the equivalence point, where the total volume was 1.50 times the original volume. At what pH does the equivalence point occur?
What mass of NH4Cl must be added to 0.750 L of a 0.100-M solution of NH3 to give a buffer solution with a pH of 9.26? (Him: Assume a negligible change in volume as the solid is added.)
Calculate the pH of a buffer solution prepared from 0.155 mol of phosphoric acid, 0.250 mole of KH2PO4, and enough water to make 0.500 L of solution.
Metacresol purple is an indicator that changes from yellow to purple at pH 8.2. (a) What is Ka for this indicator? (b) What is its pH range? (c) What is the color of a solution with pH 9.0 and a few drops of metacresol purple?