Two wires are welded together end to end. The wires are made of the same material, but the diameter of oneis twice that of the other, di = 2 d2. They are subjected to a tension of T= 4.60 N. The thin wire has alength of L2 = 40.0 cm and a linear mass density of 2 = 2.00 g/m. The combination is fixed at both endsand vibrated in such a way that two antinodes are present, with the node between them being right at theweld.(a) What is the frequency of vibration?(b) What is the length of the thick wire, L1 =?NANANo d2L,, µiL2, H2

To find the frequency and wire length-

Two wires are welded together end to end. The wires are made of the same material, but the diameter of one is twice that of the other, di = 2 d2. They are subjected to a tension of T= 4.60 N. The thin wire has a length of L2 = 40.0 cm and a linear mass density of 42 = 2.00 g/m. The combination is fixed at both ends and vibrated in such a way that two antinodes are present, with the node between them being right at the weld. (a) What is the frequency of vibration? (b) What is the length of the thick wire, L1 =? N N A N o d2 L1, HI L2, H2

Two wires are welded together end to end. The wires are made of the same material, but the diameter of one is twice that of the other, di = 2 d2. They are subjected to a tension of T= 4.60 N. The thin wire has a length of L2 = 40.0 cm and a linear mass density of 42 = 2.00 g/m. The combination is fixed at both ends and vibrated in such a way that two antinodes are present, with the node between them being right at the weld. (a) What is the frequency of vibration? (b) What is the length of the thick wire, L1 =? N N A N o d2 L1, HI L2, H2

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter1: Introduction

Section: Chapter Questions

Problem 13ETSQ

See similar textbooks

Similar questions

A high-density polyethylene [E = 135 ksi and a = 69 x 10-6/°F) block (1) is positioned in a fixture. The block is 2.1 in, by 2.2 in. by 36 in. long. At room temperature, a gap of 0.1 in. exists between the block and the rigid support at B. Assume L₁- 36 in and A = 0.1 in. Determine: (a) the normal stressa in block (1) caused by a temperature increase of 70°F. (b) the normal strain e in block (1) at the increased temperature. Answers: (a) a = (b) = i B 277.05 A LA psi. pc.
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1260 μm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. 1413 μm/m 1223 μm/m 1286 μm/m 738 μm/m 1553 μm/m
79. A mild steel flat of width 100 mm and thickness 12 mm is bent into an arc of a circle of radius of 10 m by applying a pure moment M. If Young's modulus E = 200 GPa, then the magnitude of M is (1) 72 Nm (2) 144 Nm (3) 216 Nm (4) 288 Nm
A mild steel flat of width 100 mm and thickness 12 mm is bent into an arc of a circle of radius 10 m by applying a pure moment M. If Young's modulus tilde E = 200GPa then the magnitude of M is? (a) 72 Nm (c) 216 Nm (b) 144 Nm (d) 288 Nm
A rigid bar, AB, is pinned at point B. Two other bars, AC and AD, are connected to point A to provide support for AB. We are investigating the behavior of this system under a specific load. Key Details: Bar properties: Material: Steel with Young's modulus (Esteel) of 200 GPa and coefficient of thermal expansion (a) of 11.7 x 10^-6 /°C. Cross-sectional area: AC: 1960 mm² AD: 1250 mm² Length: AC: √2 meters (square root of 2 meters) AD: 1 meter Inclination angles: AC: θ₁ (theta 1) = 30° from horizontal AD: θ₂ (theta 2) = 20° from horizontal Load on bar AB: Idealized linearly increasing load with a maximum value of 30 kN/m at point B. Problem Objectives: Determine the internal forces (axial forces) acting within bars AC and AD due to the applied load on AB. Calculate the displacement of point A in both horizontal (dA,x) and vertical (dA,y) directions.If the bar is cooled by 10°C, what would be the: Determine the internal forces (axial forces) acting within bars AC and AD…
Policie Current Attempt in Progress A steel [E = 29900 ksi, a = 6.5x10-6/°F] bar is held between two rigid supports. The bar is stress free at a temperature of 72°F. The bar is then heated uniformly. If the yield strength of the steel is 45 ksi, determine the temperature at which yield first occurs. Answer: T= i °F
A uniform beam of weight Wis supported by the two rods, the lower ends of which are at the same level just before the beam is supported, as shown in figure. The ratio of the areas Aluminium (E = 70 GPa) 2 m 1.5 m W 3 m 3m Aaluminium Asteel Steel (E = 200 GPa) 0.5 m of the rods so that the beam will be horizontal after it is attached to the rods is
The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is steel [E = 200 GPa; a = 11.7x 10-6/°C], with a cross-sectional area of A1 = 370 mm2. Bar (2) is an aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C], with a cross- sectional area of A2 = 380 mm?. The bars are unstressed when the structure is assembled. Assume a=360O mm, b=620 mm, c=730 mm, P=20 kN, and L=890 mm. After a concentrated load of P = 20 kN is applied and the temperature is increased by 35°C, determine (a) the normal stresses in bars (1) and (2). (b) the deflection of point D on the rigid bar. A (1) B (2)
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 65GPa] with a cross-sectional area of A_{1} = 850m * m ^ 2 Bar (2) is a bronze alloy [E = 100GPa] with a cross-sectional area of A_{2} = 540m * m ^ 2 Assume L_{1} = 1.9m L_{2} = 2.2m , a = 0.5m b = 1.6n , and c = 1.3 m. All bars are unstressed before the load P is applied; however, there is a 1.6-mm clearance in the pin connection at A. If a load of P = 55 KN is applied at B, determine: (a) the normal stresses Oj, 62, in both bars (1) and (2). (b) the normal strains E1, E2, in bars (1) and (2). (c) determine the downward deflection VA of point A on the rigid bar
Problem 3: Inside a steel tube, 2.4 meters long, 34 mm radius, and 1.5 mm thick, 32.5A circular bar made of aluminum with a radius of mm is inserted and these two materials arethey are linked together to form a cross section that will work. This cantilever beam obtained from end Ait is fixedly supported. This cantilever beam,A torque of T = 900 Nm from end B(torque) is applied. Stiffness modulus of steel, Strength= 77 GPa and the stiffness modulus of aluminum Gal = 26Since GPa is the rotation at point BWhat is the (torsion) angle? Calculate.
Calculate Young's modulus for an iron crystal when tension is applied along [2 -2 1] direction. S11=7.6 (TPa)-', S12 = - 2.8 (TPa)-', S44 = 8.6 (TPa) -!
A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B %3D as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm2, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A=1000 mm E-70 GPa >P=90 kN Copper L=2.0m Aa550 mm E=120 GPa