This is part two of a two-part problem. Water flows through the turbine, condenser,pump and heat exchanger in the steam power cycle shown below. Hot air flowsthrough the heat exchanger from state 5 to state 6 to heat the water before it entersthe turbine. Using the values given in the figure below, determine the thermalefficiency, nth. of the steam power cycle.AirCpo arm = 5 kg/s= 1.004 kJ/kgKTs = 400 K(6(5Heat ExchangerT5 = 1000 K(1)W,Steam Power CycleTurbineW,l= 50 kW(3(2)CondenserQc=500 kWdund This is part one of a two-part problem. Water flows through the turbine, condenser,pump and heat exchanger in the steam power cycle shown below. Hot air flowsthrough the heat exchanger from state 5 to state 6 to heat the water before it entersthe turbine. Using the values given in the figure below, determine the power outputof the turbine, WT, in [kW].Air= 1.004 kJ/kgKCPo,air%3DT6 = 400 K(6(5Heat Exchangerm = 5 kg/sT; = 1000 K'air(1)w,Steam Power CycleTurbineWel= 50 kW%3D(32)Condenser=500 kWdund

Answered: Image /qna-images/answer/097f18df-a11c-4f34-8577-1c31ba80b2a4.jpg

This is part two of a two-part problem. Water flows through the turbine, condenser, pump and heat exchanger in the steam power cycle shown below. Hot air flows through the heat exchanger from state 5 to state 6 to heat the water before it enters the turbine. Using the values given in the figure below, determine the thermal efficiency, nth. of the steam power cycle. CPo air = 1.004 kJ/kgK T6 = 400 K (5 mr = 5 kg/s %3D Heat Exchanger Ts = 1000 K (1) Steam Power Cycle Turbine Wl= 50 kW (3) (2) Condenser tor =500 kW dund

This is part two of a two-part problem. Water flows through the turbine, condenser, pump and heat exchanger in the steam power cycle shown below. Hot air flows through the heat exchanger from state 5 to state 6 to heat the water before it enters the turbine. Using the values given in the figure below, determine the thermal efficiency, nth. of the steam power cycle. CPo air = 1.004 kJ/kgK T6 = 400 K (5 mr = 5 kg/s %3D Heat Exchanger Ts = 1000 K (1) Steam Power Cycle Turbine Wl= 50 kW (3) (2) Condenser tor =500 kW dund

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Engine Cycle: Our inventor is still trying to design a heat engine that will outperform the Carnot cycle .. Design #801-456 is for an ideal, reversible engine that operates with the cycle shown below (A → B → C → D → A). The engine contains 0.421mol of a gas that has a heat capacity ratio of y = 1.300. Point Pressure [N/m²] Volume [m³] Temperature [K] A 1.05 x 105 0.010 300 B 1.85 x 105 0.010 529 1.85 x 105 0.014 751 D 1.05 x 105 0.014 426 PA B A D V (a) What is the efficiency of this engine cycle? (b) What is the efficiency for a Carnot cycle working between the same maximum and minimum temperatures?
Writhe the full solution using thermodynamics equation. Steam at 14 bar & 315 C [state 1] enters a turbine through a 75 mm diameter pipe with a velocity of 3 m/s. The exhaust from the turbine is carried through a 250 mm diameter pipe and is at 0.35 bar & 105 C [state 2]. What is the power output of the turbine in watts? HInt: Use the steam table to obtain the thermodynamics property of the steam at the specified conditions.
Consider a compressor which is adiabatic. At the inlet of the compressor the temperature is 360 K and pressure is 130 kPa and the air passes at the rate of 1 kg/s. At the exit of the compressor the temperature is 550 K and pressure is 900 kPa. Find the volumetric flow rate of air at the exit [m³/s] and also, power consumed by the compressor [kW]. Assumptions. Steady state process. Kinetic and potential energy changes are negligible. Air is an ideal gas with variable specific heats.
Consider a compressor which is adiabatic. At the inlet of the compressor the temperature is 380 K and pressure is 130 kPa and the air passes at the rate of 1 kg/s. At the exit of the compressor the temperature is 530 K and pressure is 785.7 kPa. Find the volumetric flow rate of air at the exit [m/s] and also, power consumed by the compressor [kW]. Assumptions. Steady state process. Kinetic and potential energy changes are negligible. Air is an ideal gas with variable specific heats.
Mike is trying to determine the amount of work his experimental air compressor is doing. He finds that the amount of work done (W) depends on the rate of change in pressure created by the pump (dP/dt) with respect to time, the volume of air inside the pump (V) and the speed at which air moves out of the pump (v).Using the information provided above, determine the simplest expression that Mike can use to determine the work done by his pump that is dimensionally correct. After an initial test run Mike determines that his pump does 160 J of work (W1). Calculate the amount of work (W2) in J that Mike would expect his pump to do if its volume were 4.5 times greater. If Mike wanted to reduce the volume of his pump by a factor of 7.5, yet keep it doing the same amount of work at the same airspeed, by what numerical factor (B) would he have to increase the rate of change in pressure (dP/dt) his pump creates?
The correct statement in relation to first law of thermodynamics i.e. Q=W+AU is, .. [A] Q is negative if heat is absorbed by the system and Q is positive if heat is released by the system [B] AU is negative if internal energy of the system increases and AU is positive if internal energy of the system decreases [C] W is positive if work is done on the system and W is negative if work is done by the system [D] Q is a path function, W is a path function and A U is a state function
Problem-1 Calculate the efficiency of Carnot heat engine working between high temperature reservoir(source) T1 , and low temperature reservoir (sink) T2, for each case as described in the following table. High temperature reservoir(source) T[K] 1000 Low temperature reservoir(sink) T2[K] Carnot Efficiency,Ncarnot 300 1000 150 1000 100 1000 400 1000 500 1000 600 1000 750 1000 950 1000 999 750 300 600 300 500 300 400 300 300 300 1000 -500
A heat pump is an electrical device that heats a building by pumping heat in from the cold outside. In other words, it's the same as a refrigerator, but its purpose is to warm the hot reservoir rather than to cool the cold reservoir (even though it does both). Let us define the following standard symbols, all taken to be positive by convention:Th = temperature inside buildingTe = temperature outsideQh heat pumped into building in 1 day Qe = heat taken from outdoors in 1 dayW = electrical energy used by heat pump in 1 day Explain why a heat pump is better than an electric furnace, which simply converts electrical work directly into heat. (Include some numerical estimates. )
Air passes along an insulated horizontal pipe of 0.05 m2 cross sectional area. In the pipe it passes over a heating element. It enters at 20 degrees C, 1.013 bar and 30 m/s. Rair = 287 J/kg.K and Cp=1005 J/kg.K (a) Determine the mass flow rate of the air. [ Select ] O kg/s (b) Determine the temperature of the air at the exit if the pressure is 1.5 bar (you may assume velocity change is negligible) [ Select ] (c) Determine the rate of heat input [ Select ] O kW
A vertical piston-cylinder arrangement with a diameter of 120 mm contains water with a quality of 60%. The pressure is 3 bar. Initially the piston rests 40 mm above the bottom of the cylinder. Heat is then added until the volume is 3 times the original volume. (a) Determine the mass of the water in the cylinder [ Select ] kg (b) Determine the work done. [ Select ] (J) (c) The final temperature [Select ] °C (d) The heat transferred to the system 1.8 kJ
A refrigeration unit maintains the interior temperature of a walk-in meat locker at a temperature of – 5°C. The rate of heat transfer to the locker from the outside air is 8000 kJ/hr. The air outside the locker is at 22°C. The coefficient of performance [COP] for the actual refrigeration unit is 2.5 to maintain the locker temperature. Assume [3]: пМax [Тн,Tc] %- ВМах [Тн, Тc] - YMax| [TH,Tc] 1. The maximum coefficient of performance [COP] for the refrigeration cycle is equal to а. 2.50 b. 9.93 с. 10.93 d. none of the above. 2. The heat transfer to the locker from the outside air to the locker is equal to а. QNet b. Qc с. Он d. none of the above. 3. The required power input Wactual for the cycle in kJ/hr is 3,200 b. 8,000 с. 20,000 а. d. none of the above. 4. The minimum power input WMin for the cycle in kJ/hr is а. 730 b. 805 с. 3200 d. none of the above. 5. The required power input WActual for a cycle with a COP of 5 in kJ/hr is 1,600 4,000 с. 10,000 d. none of the above. а. b.
1. Refrigerant R-22 with the mass of 2 kg is located inside the sealed container, initially saturated vapor at 6.8 bar. Heat was added to refrigerant and final pressure reached 20 bar according to pv=const. Neglecting the kinetic and potential energy changes determine: Internal energy change in [J] Heat added to the refrigerant in [J] and work done by fluid in [J]. 3.draw the Temperature-volume diagram showing all stages. 4.What do you think about the final stage condition? Is it gas, liquid-gas, or liquid stage? Use energy balance equation and find all unknowns using the NIST webbook.