The wooden members A and B are to be joined by plywood splice plates, that will be fully glued on the surfaces in contact. As part of the design of the joint and knowing that the clearance between the ends of the members is to be 1/4 in., determine the smallest allowable length L if the average shearing stress in the glue is not to exceed 120 psi.

The wooden members A and B are to be joined by plywood splice plates, that will be fully glued on the surfaces in contact. As part of the design of the joint and knowing that the clearance between the ends of the members is to be 1/4 in., determine the smallest allowable length L if the average shearing stress in the glue is not to exceed 120 psi.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

The two pieces of wood, 2 in. by 4 in., are glued together along the 40o joint. Determine the maximum safe axial load P that can be applied if the shear stress in the glue is limited to 250 psi
– A joint is made by gluing two plywood gussets of thickness t to wood boards.The tensile working stresses are 1200 psi for the plywood and 700 psi for the woodboards. The working shear stress of the glue is 50 psi. Determine the dimensions’ b and tso that the joint is as strong as the boards.
Two pieces of wood are glued together, find the maximum load which the glued wood could carry that must not exceed 12 MPa normal stress and 7 MPa shear stress. P 30° P 100 mm Glued Section 100 mm
The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the surfaces in contact. The clearance between the ends of the members is to be 11 mm, the length of the plywood is L = 288 mm and the width of the wood is W = 119 mm. Find the shearing stress (in Mpa) in the glue if P = 35.9 kN. Round off the final answer to two decimal places.
The laminated beam, shown in cross section, is composed of ?ve 6- in. by 2-in. planks that are glued together. The beam carries a uniformly distributed load of intensity wə over its 8-ft simply supported span. If the working stresses are 75 psi for shear in glue, 90 psi for shear in wood, and 800 psi for bending in wood, 6 in. 5 @ 2 in. = 10 in.
A square post which is made up of two parts is glued at plane abcd with the angle α = 30° with the vertical. Allowable compressive stress @ glue = 5.2 MPa Allowable shearing stress = 3.5 MPa P = 36 kN. )What is the minimum post dimension, w (mm), without exceeding the allowable compressive stress at the glue? 2.) What is the minimum post dimension, w (mm), without exceeding the allowable shearing stress at the glue? 3.)What angle, α, will give the maximum shearing stress?
A 5 ft. long laminated wood beam is built up by gluing together three 2” x 6” boards to form asolid beam 6” x 6” cross section, as shown in the figure. Calculate the maximum allowable valueof P (lb.) such that both the (1) allowable shear stress in the glued joints of 100 psi and the (2)allowable bending stress of 1200 psi is not exceeded. (Disregard the weight of the beam).[Formula: Bending Stress:  = (M)(y)/I; max = (M)(c)/I; Transverse Shear Stress:  =(V)(Q)/(I*t); max = (V)(QNA)/(I*tNA)]
Question 2A composite bar is made up of a steel strip 2 mm thick and 12 mm wide, sandwichedbetween two aluminium strips each 3 mm thick and 12 mm wide. The three strips areheld together by two rivets of 5 mm diameter each.2.1 Make a neat detailed sketch of the assembly.2.2 If the three strips are fastened together at 15 0C, determine the shear stress set up inthe rivets when the temperature is raised to 21 0C.Note: The resistance of a rivet in double shear may be taken as 1.75 times the resistancein single shear.(For steel: E = 200 GPa and α = 11×10 -6/ 0C)(For aluminium: E = 70 GPa and α = 22×10-6/0C)
Determine the minimum dimension h to the nearest 1/8 in. of the beam’s cross section to safely support the load. The wood has an allowable normal stress of 2 ksi and an allowable shear stress of 200 psi
The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the surfaces in contact. The clearance between the ends of the members is to be 11.4 mm, the length of the plywood is L = 316 mm and the width of the wood is W = 98 mm. Find the largest possible value of P (in N) if the average shearing stress in the glue is not to exceed S = 810 kPa.
1. Figure shows two wood members are joined together using a 60 degrees wood glue adhesive. Find the average normal and shear stress resisted in the plane of the connection. 25 mm 8 kN- 8 kN 60° 30 mm
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?