The solid 32 mm diameter steel [E - 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a rollersupport and that the bearing at D can be idealized as a pin support. For the loading shown, determine:(a) the shaft deflection at pulley A.(b) the shaft deflection at pulley C.Assume P- 500 N, Q- 950 N, Las - 450 mm, Lạc - 650 mm, Lco - 650 mm.ABCDLABLBCLCDPart 1Calculate the area moment of inertia for the solid circular cross-section.Answer:|- imm4

Given, A solid circular shaft, Diameter= D = 32mm P = 500N Q= 950N Modulus of elasticity = E =…

The solid 32 mm diameter steel [E- 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (2) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P- 500 N, Q - 950 N, Las - 450 mm, Lsc- 650 mm, Lco - 650 mm. B C LAB LBC LCD Part 1 Calculate the area moment of inertia for the solid circular cross-section. Answer: |- i mm

The solid 32 mm diameter steel [E- 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (2) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P- 500 N, Q - 950 N, Las - 450 mm, Lsc- 650 mm, Lco - 650 mm. B C LAB LBC LCD Part 1 Calculate the area moment of inertia for the solid circular cross-section. Answer: |- i mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bar AB is attached at A as fixed support. A small spaces can be seen on the other side of the bar prior to another rigid surface. Load P is applied on the bar located at two-thirds of length L from point A. Determine the small space s if the support reactions at A and B are to be equal due to the external load P. See all necessary parameters below. L A E P A 3 m 2500 mm² GPa 45 77 KN 2/3 -L 113 mm -L ANSWERS: ALL ANSWERS SHOULD BE IN THREE (3) DECIMAL PLACES INCLUDING ZEROS 01 (delta due to external load P) = 52 (delta due to Reaction at B) = Small Space s = mm S₁ mm B
Dr. A H.W.5: A rigid bar ABCD is supported by two bars, as shown in Fig- ure 3 .There is no strain in the vertical bars before load Pis applied. After load P is applied, the normal strain in rod (1) is -570 pm/m. Determine (b) the normal strain in rod (2) if there is a l-mm gap in the connection at pin C before the load is applied. (c) the normal strain in rod (2) if there is a l-mm gap in the connection at pin B before the load is applied. (a) the normal strain in rod (2). (2) 1,500 mm 360 mm 140 mm 240 mm Rigid bar bber C B 900 mm (1)
D 2a В 4а 2a 4a E 390 The columns AC and DE are connected to the bars BD and CD by pins. The support at A is a pin and the support at E is a roller. Determine the forces acting on each column due to the horizontal linearly distributed load on AC and vertical unifrom load on CD. Present your solution as two FBDS showing the actual forces.
The hand brake for a bicycle is shown. Portions DE and FG are free to rotate on bolt A which is screwed into the frame BC of the bicycle. The brake is actuated by a shielded cable where T1 is applied to point E and T2 is applied to point G. A spring having 60 N compressive force is placed between points E and G so that the brake stays open when it is not being used. Assume the change in the spring's force is negligible when the brake is actuated to produce the forces P = 350 N at points D and F. cable T2 spring o ma (a) Determine the necessary cable force (N) T2. (a) 348.33 (b) 526.67 (c) 545.25 (d) 421.01 80 mm (c) Determine the force (N) exerted by FG on bolt A. (a) 481.33 (b) 703.78 (c) 651.79 (d) 430.48
E 10-59. The A-36 hollow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is rotating at 80 rad/s, it transmits 32 kW of power from the engine E to the generator G. Determine the smallest thickness of the shaft if the allowable shear stress is 7allow = 140 MPa and the shaft is restricted not to twist more than 0.05 rad.
The rigid bar AD (figure STR-4) is supported by two steel wires of 1.5mm diameter (E = 200 GPa) and a pin and bracket at D. Knowing that the wires were initially taut. Determine the following: a. The additional tension in wire BE when a load P=900 N is applied at D. b. The additional stress in wire FC when a load P = 900 N is applied at D c. The corresponding deflection at point D.
12-2. The L2 steel blade of the band saw wraps around the pulley having a radius of 12 in. Determine the maximum normal stress in the blade. The blade has a width of 0.75 in. and a thickness of 0.0625 in. Prob. 12-2 12 in.
At what distance a should the bearing supports at A and B be placed so that the deflection at thecenter of the shaft is equal to the deflection at its ends? Use MAM. The bearings exert only on theshafts. The flexural rigidity is constant.
. Determine the magnitude of the moment of the 600-N force acting on the bracket shown. Expressyour un answer in Nm.
*R9 4. Two A36 steel pipes, cach having a cross-sectional area of 200 mm, are screwed together using a union at B as shown. Originally the assembly is adjusted so that no load is an the pipe. If the union is then tightened so that its screw, having a lead of 0.55 mm, undergoes two full turns, determine the average normal stress developed in the pipe. Assume that the union at B and couplings at A and C are rigid. Neglect the size of the union. Note: The lead would cause the pipe, when unloaded, to shorten 055 mm when the union is rotated ane revolution. -09m- a6 m.
4-5 The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is 60 mm², determine the displacement of B and A. Neglect the size of the cou- plings at B, C, and D. 60° 3.30 KN 2 kN D C B A 8 kN 60⁰ 3.30 KN 0.75 m 1.50 m 0.50 m 2 kN
Answer the problem below, following the GIVEN-REQUIRED-SOLUTION format. Please provide the FBD. Problem: The pin spanner is used to turn shafts and collars. If a moment of is required to turn the 200-mm-diameter collar about its center O under the action of the applied force P, determine the contact force R on the smooth surface at A. Engagement of the pin at B may be considered to occur at the periphery of the collar.