Answered: The internal loadings act on the…

The internal loadings act on the section. Show the stresses with their directions that each of these loads produce on elements located at points from A to D.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Related questions

Q: For the given state of plane stress in the r-y plane, determine (a) the maximum in-plane shear…

Q: Determine the average nommal stress developed at points A, B, and C. 1 attachment 5.2 cm 4 cm 4 cm…

A: Normal stress acting at point A is σA=FA=4Fπd2=43 kipπ1.5748 in2=1.540 kip/in2 4 cm=1.5748 in

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

Q: Determine the torsional stress in the thin-walled tube as shown:

Q: Q/ If the cross section of the femur can be approximated as a circular tube, determine the state of…

A: Consider the diagram shown below for the femur. At point A, there will be a shear stress because of…

Q: f F1 = 1070 lb and F2 = 2095 lb, determine the magnitude of the normal stress produced at point H.…

A: Given that , F1=1070lbF2=2095lb

Q: Take the section AB, construct the FBD and label the internal loadings, determine the normal stress…

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: remove 3 kW, 4 kW, and 5 kW respectively, determine the maximum shear stress developed in the shaft…

Q: Determine the maximum normal stress that loading produces in the steel member.

Q: Q1) The cantilever beam is subjected to axial load as shown Below, determine the actual stresses…

A: Solution: Let forces,P1=10kNP2=15kNP3=20kN Total tensile force acting on the section…

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A: The forces and torques at point B are shown as, On using equilibrium of forces in x, y, and…

Q: Determine the state of stress at point A on the cross section of the pipe assembly at section a–a.…

Q: For the given state of stress, determine the normal and shearing stresses exerted on the oblique…

Q: The average normal stress and maximum in-plane shear stress components are determined from the…

A: Yes, the average normal stress and the maximum in-plane shear stress components are determined from…

Q: The state of stress at a point is shown on the element. Determine (a) the principal stress and (b)…

A: (a) Write stresses that are shown in the element. σx=240 MPaσy=100 MPaτxy=80 MPa

Q: The steel tube below has an inside diameter of 2.75”, and an outside diameter of 3”. If the tube is…

A: The polar moment of inertia of the bar can be determined as,

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kNforce is applied to the…

Q: The internal loadings at a section of the beam are shown. Determine the in-plane principal stresses…

A: Given, I section Px =-80 kN = -80 X 103 N My=-500 Nm Mz=10 kNm =10 X 103 Nm

Q: Determine the average punching shear stress the circular shaft creates in the metal plate through…

A: Given data: The value of shear load is F=40 kN The diameter of shaft is dAB=50 mm The thickness of…

Q: a) Determine the internal forces acting at s b) Determine the stress components that ac =…

A: INA=2.6525×10-7m4 To-Find:- a) The internal forces acting at section a-ab) The stress components…

Q: a) the principal stresses; and (b) the maximum in-plane shear stress.

Q: Determine the normal stress developed at points A and B. Neglect the weight of the block.

A: The sum of forces in the horizontal direction, ∑FX=-6 kips -12 kipsF=-18 kips The expression of the…

Q: Determine the shear stresses experienced by the four identical circular bolts of diameter 20 mm used…

A: Given data: F = 150 kN d = 20 mm Need to determine the shear stress in each bolt.

Q: element, the normal and shear stresses gure. Determine the normal and shear el to the xy axes; that…

Q: The solid rod is subjected to the loading shown. Determine the state of stress at point B, and show…

A: Given data:

Q: loadng is suspender bars. AB and EF are made from aluminum and CD is made from steel. If each bar…

A: given:area of cross section A=450mm2σallowst=180mpaσallowal=94mpaEst=200gpaEal=70gpa

Q: Determine the average normal stress developed in rod AB if the load has a mass of 64 kg. The…

Q: The solid cylinder having a radius r is placed in a sealed container and subjected to a pressure p.…

A: Explanation: ◆ The solid cylinder is subjected to a pressure p inside the sealed cylinder. ◆ The…

Q: Determine the equivalent state of stress on an element at the same point that represents the maximum…

A: Given: σx=100 kPaσy= 700 kPaτxy=400 kPa To find state of stress on an element at the same point…

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the state…

A: The given beam is subjected to three loads- axial load, shear load and bending moment. Therefore…

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

Q: Determine the stresses at point A. The circular solid shaft has a radius of 40 mm. 300 тm 200 mm B.…

A: Given Data, F= Eccentric shear force = 30 KN r= Radius of the shaft = 40mm According to the diagram…

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A: The free body diagram of beveled gear is shown below:

Q: (a) The reaction forces at the two ends of the shaft A and D. (b) The bending moments at shoulder…

Q: Determine the equivalent state of stress on an element at the same point oriented 45° clockwise with…

A: Given Data: The value of σx=0 The value of σy=-400 kPa The value of τxy=-300 kPa The angle of…

Q: The bar has a constant width of 35 mm and a thickness of 10 mm. Determine the maximum average normal…

Q: The box beam is subjected to the 26-kN force that is applied at the center of its width, 75 mm from…

A: Given, P = 26 kN

Q: The bent shaft is fixed in the wall at A. If a force F is applied at B, determine the stress…

A: ∑Fx=0; Vx-13cos 45ο=0⇒Vx=9.19 lb∑Fy=0; Ny-13 cos45ο=0⇒Ny=9.19 lb∑Mx=0; Mx-13…

Q: If the box wrench is subjected to the 50-lb force, determine the principal stresses and maximum…

A: Draw the section a-a with shear force and bending moments. Apply force equilibrium in the…

Q: Three forces are applied to the bar shown. Determine the normal and shearing stresses at (a) point…

A: Given Data The load acting on the beam is: P=10 kN The shear load is: V=750 N The horizontal load…

Q: The bar has a cross-sectional area A and is subjected to the axial load P. Determine the average…

A: Applying equilibrium conditions :∑ Fx=0⇒V-Pcosθ=0⇒V=Pcosθ∑ Fy=0⇒N-Psinθ=0⇒N=PsinθCross sectional…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

The internal loadings act on the section. Show the stresses with their directions
that each of these loads produce on elements located at points from A to D.
NB
M.
Internal loadings
N
M
V
Element at point A
Element at point B
Element at point C
Element at point D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A body is subjected to multiple applied loads. The resultant stress at point location (0, 1, 4) meters can be described as or = -5 MPa. Which of the following describes t stress state at this point? Biaxial tension Uniaxial compression Pure shear Uníaxial tension
200 mm diameter rod is subjected to loads as shown. Determine the state of stress at points A and B. Show your results on an infinitesimally small square plane (please use the ones drawn below, which helps you in directions). 8 m 600 N 10 m 400 N 700 N + Oz Tyz + Txy Ox Oy A
Determine the state of stress at point A of the rectangular post shown loaded with concentrated forces directed along the y axis equal to 75kN and along the x axis equal to 15kN. 1)Determine the total normal stress along the x and y axes at point A (include if tensile or compressive in your final solutions) 75 kN 50 mm 200 mm- 150 mm OAx= 15 kN OAy= 2) Draw the state of stress of point A 800 mm A 50 mm
USE the mohr's circle method to determine the stress components acting on the inclined plane AB USE THE MOHR'S CIRCLE METHODE NOT THE ONE IN THE QUESTION