The force-deflection relationship for a 200-pound digital device supported on an elastomeric mounting is F(x) = 600 x + 30 x³, where the force (F) and the deflection (x) are in pounds and inches, respectively. Determine the following: a. The equivalent linear spring constant of the mounting at its static equilibrium position. b. The deflection of the mounting corresponding to the equivalent linear spring constant

The force-deflection relationship for a 200-pound digital device supported on an elastomeric mounting is F(x) = 600 x + 30 x³, where the force (F) and the deflection (x) are in pounds and inches, respectively. Determine the following: a. The equivalent linear spring constant of the mounting at its static equilibrium position. b. The deflection of the mounting corresponding to the equivalent linear spring constant

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. For a particular thermocouple, if one junction is maintained at 0°C (cold junction) and the other junction is used as a probe to measure the desired Celsius temperature t, the voltage V generated in the circuit related to the temperature t as V = t (a + bt) Further, for this thermocouple, when V is in millivolts, the two constants are a = 0.25 and b = -5.5 x10+. Determine the value of V if the measured temperature is 100°C.
122 1.17 The tripod shown in Fig. 1.73 is used for mounting an electronic instrument that finds the distance between two points in space. The legs of the tripod are located symmetrically about the mid-vertical axis, each leg making an angle a with the vertical. If each leg has a length / and axial stiffness k, find the equivalent spring stiffness of the tripod in the verti- cal direction. CHAPTER 1 FUNDAMENTALS OF VIBRATION FIGURE 1.73 A tripod carrying an electronic instrument.
Q3/ In real life engineering application, it is required to design a spring in train, which one of the following materials in the table below should be choose, justify your answer ? used correct units? Poisson's Yield Strength Modulus of Elasticity 106 psi Material MPа psi GPa Ratio 30 0.30 120000 207 Steel alloy Brass alloy Aluminum alloy Titanium alloy 830 0.34 0.33 380 55000 97 14 275 40000 69 10 690 100000 107 15.5 0.34
1. Determine the equivalent spring stiffness constant of the following. 150 N/m 240 N/m 60 N/m wwwwwww 290 N/m 105 N/m wwwwww 35 N/m a. 250 N/m www 145 N/m F Ans:
True or false Degree of freedom of a mechanical system define its configuration by the number of independent parameters
Determine the equivalent spring stiffness constant of the following. 235 N/m 155 N/m 350 N/m wwwwwwwwwww 140 N/m 325 N/m ww www 100 N/m www F Answer:
The mass attached to the end of a helical pull spring statically forces the spring to pull, and 100 mm static elongation in the spring references The same mass is attached to the end of this spring, and the mass is released vertically from a height of 0.6 meters how many times does the force on the spring increase according to the static loading state when it is released? 4.32 O 4.87 5.36 5.12 18110140 O 4.60
PHYS X PHYS X 印 PHYS X PHYS X POTPHYS X PHYS X E PHYS X E PHYS top/semester2/physics%20for%20engineers/PHYS220_CH15_Lecture%20Notes_Problems%2015 19,15.29 S (D Page view A Read aloud V Draw Problem-15-19: page-475 A 0.500-kg object attached to a spring with a force constant of 8.00 N/m vibrates in simple harmonic motion with an amplitude of 10.0 cm. Calculate the maximum value of its (a) speed, and acceleration. (b) the speed and the acceleration when the object is 6.00 em from the equilibrium position, and (c) the time interval required for the object to move from.r50 to r5 8.O0 cm. Solution:
A force of F = 50 N is applied to the rope that causes the angle 0₁ = 60 degrees to keep the system at equilibrium. The N spring constant is k = 100 m B a 0₁ с a b с Variable Value 2 m 2 m 2 m F b Values for the figure are given in the following table. Note the figure may not be to scale. cc i❀O BY NC SA 2013 Michael Swanbom
2. Below is a picture of a car suspension system with additional springs (in red) added in series. Assume the car remains "level" (i.e. no rotational motion of the car body, only vertical motion). The original springs are ks modeling tire/road interaction). The car mass is m = 2,000 kg. 20, 000 N/m (the suspension spring), and kt 100, 000 N/m (the spring %3D The springs are all in equilibrium when d = 0.4 m. Ignore gravity in this problem. The point of the additional spring k is to make the ride more "bouncy" (some people like it that way). However, you need to make sure the car does not "bottom out" (i.e. hit the bump). It is known that when the springs are unstretched/uncompressed, the marimum vertical velocity can be is 1 m/s. What is the minimum value of the spring constant k (of the additional red spring) so that the car does not hit the bump during its vertical oscillations. Hint: Use energy balance. kis k's kt Figure 4: Simplified car model with upper springs representing…
A spring with an un-stretched length of 5 in expands from a length of 2 in to a length of 4 in. The work done on the spring is . in .lb. (A) k (2 in)2 (B) k [(4 in)? - (2 in)2] (C) - k [(4 in)? - (2 in)?] (D) k [(3 in)? - (1 in)*]
In a linear spring finite element model, as per the finite element model’s sign convention, which one of the following statements is true? Select one: a. If Fe1 is negative then the spring is under compression b. If Fe2 is negative then the spring is under tension c. If Fe1 is positive then the spring is under tension d. If Fe2 is positive then the spring is under tension