The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment (1) is a tube with an outside diameter of D₁ = 3.95 in., a wall thickness of t₁ = 0.25 in., and a shear modulus of G₁ = 4,000 ksi. Steel segment (2) is a tube with an outside diameter of D₂ = 2.10 in., a wall thickness of t₂ = 0.125 in., and a shear modulus of G₂ = 12,000 ksi. The compound shaft is subjected to torques applied at B and C as shown. Determine the rotation angle of C with respect to the support at A. (1) 9 ft -0.0276 rad -0.0202 rad O -0.0320 rad O -0.0374 rad O -0.0261 rad 1,700 lb-ft B (2) 6 ft 650 lb-ft

The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment (1) is a tube with an outside diameter of D₁ = 3.95 in., a wall thickness of t₁ = 0.25 in., and a shear modulus of G₁ = 4,000 ksi. Steel segment (2) is a tube with an outside diameter of D₂ = 2.10 in., a wall thickness of t₂ = 0.125 in., and a shear modulus of G₂ = 12,000 ksi. The compound shaft is subjected to torques applied at B and C as shown. Determine the rotation angle of C with respect to the support at A. (1) 9 ft -0.0276 rad -0.0202 rad O -0.0320 rad O -0.0374 rad O -0.0261 rad 1,700 lb-ft B (2) 6 ft 650 lb-ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3- A cylindrical thin-walled pressure vessel was made by welding components together in a helical pattern, as shown in the figure. If the internal pressure within the vessel is p = 0.3 MPa, determine the normal stress perpendicular to the weld line and the shear stress tangential to the weld line. 400mm •t=8mm 21 weld line X
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig. P-108. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. Figure P-108 PARTNER Aluminum A=400 mm² Steel A = 500 mm² 2.5 m 2.0 m Bronze A = 200 mm² 1.5 m 2P
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-
A bar obtained by bonding together pieces of steel (Es = 29 x 106 psi) and brass (E = 15 x 106 psi) has the cross section shown (Fig. a). Determine the maximum stress in the steel and in the brass when the bar is in pure bending with a bending moment M = 40 kip-in. 0.4 in. 3 in. Brass 0.75 in. Steel Brass 0.4 in. (a) 1) Composite bar.
In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is Og = -90 MPa and the initial temperature %3D 20°C. 2) The final length of the aluminium member. Aluminum A=1800mm? Bronze A=1500mm? E=73GPA E=105GPA a=23.2x10-6/°C a=21.6x10-6/°C Gap=0.5mm 0.35m 0.45m
An aluminium rod is rigidly attached between a steel rod and a bronze rod as shown in Figure 3. Axial loads are applied at the positions indicated. (a) Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminium of 90 MPa, or in bronze of 100 MPa. (b) Using the answer from question (a), determine the total elongation of the rods. Steel Aluminium A = 500 mm? Bronze A = 400 mm? E = 200 GPa A = 200 mm? F = 70 GPa E = 83 GPa 4P 2P 2.5 m 2.0 m 1.5 m Figure 3
Question 2) Knowing that a 0.02-in. gap exists when the temperature is 75 °F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. -14 in. Bronze A = 2.4 in² E = 15 x 10 psi a = 12 x 10-6/°F -18 in.- Aluminum A = 2.8 in² E = 10.6 x 105 psi a = 12.9 x 10-6/°F
A 5.2-m-long aluminum tube (1) is to be connected to a 2.2-m-long bronze pipe (2) at B. When put in place, however, a gap of 9 mm exists between the two members, as shown. Aluminum tube (1) has an elastic modulus of 69 GPa and a cross-sectional area of 1980 mm2. Bronze pipe (2) has an elastic modulus of 93 GPa and a cross-sectional area of 3970 mm2. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses ?1, ?2 produced in each of the members. (b) the displacement (change in length of material (2), up is positive) uB of flange B with respect to support A. 5.2 m 2.2 m Answers: (a) 0₁ = (b) Ug = C (1) B (2) -95.40 1.126 9 mm MPa, 0₂ = mm. -47.58 MPa
An aluminum alloy [E = 67 GPa; ν = 0.33; α = 23.0 × 10–6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 225 mm, a cross-sectional area of A = 5100 mm2, and a length of L = 4.1 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by ΔT = 63°C, the longitudinal normal strain in the plate is found to be 2900 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Δd.
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
As shown, an aluminium alloy construction BCD with a circular cross section is fixed at end B and affected by a force of 150 N at the free end D. The diameter of the cross-section a-a is 20 mm. The yield strength of the material is 80 MPa: a) Determine the stresses at point A of the a-a cross-section. As indicated in the picture, draw the stress element in Cartesian coordinates and specify the stress values.(b) Calculate the factor of safety, n for Tresca, and the von Mises yield criterion to see if the structure would yield based on the stresses at point A.(c) In the major stress area, draw the yield loci of both criteria and indicate the operational stress state & why is the Rankine failure criterion inappropriate for aluminium alloys?