Steel rod AB bonded to the brass rod BCD as shown below. The steel rodhas a diameter of 50 mm while the brass rod has an outer diameter of40mm with segment BC being hollow with an inner diameter of 20 mm. Ifthe assembly is loaded as shown, solve for thea. magnitude of the internal torque in the steel section (TAB)b. maximum shear stress in the steel section (TAB)C. maximum shear stress developed in the whole assembly (Tmax)0.60 kNmA 1.80 kNm2.0m2.0m2.0m

Answered: Image /qna-images/answer/7a4dc4d9-d64f-4263-bf9b-f5f20e993e53.jpg

Answered: Steel rod AB bonded to the brass rod…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

Two equal gear wheel of 360 mm p.c.d and 6 module are in mesh if the pressure angle 20 determine the maximum addendum necessary if there are always to be at least two pairs of teeth in contact . if the gear wheels rorates at 110 r.p.m and 6 kw is being transmetted find the normal force between the teeth assuming that the total force is dividing equally between the two pairs of teeth Neglect the frection. (Ans 6.8mm , 1.54KN .)
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 The shaft is mounted on two 400 400 270 250 210 640i ]640 100
Q1: The arrangement of a transmission brake is shown in the figure. The arms are pivoted at O and, when force is applied at the end of the hand lever, the screw AB will rotate. The left-and right- hand threads working in nuts on the ends of the arms will move the arms together and thus apply the brake actuating force equally. A B 12cm The drum is 17.75cm diameter, and the angle subtended by each block is 90°. the friction material lining width is 4cm. Assuming a coefficient of friction for the braking surfaces that is equal to 0.30 Determine the force required by the screw AB to set the brake torque on the drum equal to 200 N-m. 17 75cm 12cm 46 35cm Torqueleft= TorqueRight= 97.40 N.m 6 35cm 102.60 N.m
a b c d h 82 mm 139 mm 39 mm 18 mm 33 mm Clamps like the one shown are commonly used in woodworking applications. This clamp has the dimensions given above, and its jaws are 38 mm wide (in the direction perpendicular to the plane of the picture). The screws of the clamp are adjusted so that there is a uniform pressure of 190 kPa being applied to the workpieces by the jaws. Find the force carried in each screw.Note: Assume that A, B, C, and D act as pins. (Denote tension forces with positive values; compressive forces with negative values.)
The 500 N load is acting on the helical compression spring with 20 number of turns. The helical spring is having the mean diameter of 12cm,spring wire diameter is 6mm. Find the spring inside diameter. Select one: O a. 114 mm O b. 52mm O c. 150mm O d. 20mm
CB Page view A Read aloud Add text V Draw Highlight A 550 rpm shaft fitted with a 35 inches diameter pulley weighing 300 lbs. This pulley delivers 40 Hp to a load. The shaft is also fitted with a 26 inches pitch diameter gear weighing 220 lb. This gear delivers 30 Hp to a load. Assume that the tension of the tight side of the belt is twice that on the slack side of the belt, determine the concentrated loads produced on the shaft by the gear in Ibs. Select one: a. 753.85 b. 462.61 C. 484.44*** d. 264.44
thick lnange be! The total torque required to turn the double threaded power screw is 55 N.m. If the screw turns at 285 rpm and the pitch of 4mm, find: A. The horsepower input of the power screw. B. The efficiency if the weight loaded is 10 kN.
d = 30 mm diameter, solid, ductile no.11 m from end A of vertical shaft AB made of materialtightly fitted to a radius disc, at end B to the groundfixed. From the C point of the disk - parallel to the y axisA force of F = 20 kN will be applied. Safety of the shaftcontrol according to Tresca criterion and Von-Mises criteriondo. (Due to the tight fit, the shaft is in the hole in the disc.cannot rotate freely.)
A spur gear transmits 35 N · m of torque to the 20-mm-diameter driveshaft. The 5-mm-diameter setscrew threads onto the gear’s hub, and it is received in a small hole that is machined in the shaft. What's the factor of safety aganist yield under shear loading
A crank loaded by a force F 1300 N that causes twisting and bending of a 20 mm -in-diameter shaft. (a) Draw separate free-body diagrams of the shaft AB and the arm BC, and compute the values of all forces, moments, and torques that act. Label the directions of the coordinate axes on these diagrams. BC and indicate where these act. (b) Locate a stress element on the top surface of the shaft at A, and calculate all the stress components that act upon this element. (c) Determine the maximum normal and shear stresses at A.
Adjustable pliers hold a round metal bar as a machinist grips the handles with P = 43 N. Using the free body diagram shown for the combined lower jaw and upper handle, calculate the force A that is applied to the bar. Assume lh = 160 mm and l2 = 15 mm. (Express your answer using three significant figures.) A =
The shaft, is driven by pulley B from an electric motor. Another belt drivefrom pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratioof belt tensions for pulley B is 3.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensilestress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion andbending factors as 1.25 and 1.75 respectively, find the shaft diameter.Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare theweights of the two shafts. [Ans. 30 mm ; 24 mm ; 1.82 Given Length CD=350mm Length AB=150mm Length BD=100mm The total length is CD =350

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS