Solve the following problem using Geometric Programming In a three-stage compression system, air enters the first stage at a pressure of 100 kPa and a temperature of 20 °C. The exit pressure from the third stage is 6400 kPa. Between stages the air is passed through an intercooler that brings the temperature back to 20 °C. The expression for the work of compression per unit mass in an ideal process is k ART. [1-(22)(-1)/*] -RT₁ k-1 where subscript 1 refers to the entering conditions and subscript 2 to the leaving conditions. a) With the intermediate pressures chosen so that the total work of compression is a minimum, what is the minimum work required to compress 1 kg of air, assuming that the compressions are reversible and adiabatic? b) What are the intermediate pressures that result in this minimum work of compression? c) Discuss the relative energy consumption by each compressor and the progression of the pressure through the three compressors.

Solve the following problem using Geometric Programming In a three-stage compression system, air enters the first stage at a pressure of 100 kPa and a temperature of 20 °C. The exit pressure from the third stage is 6400 kPa. Between stages the air is passed through an intercooler that brings the temperature back to 20 °C. The expression for the work of compression per unit mass in an ideal process is k ART. [1-(22)(-1)/*] -RT₁ k-1 where subscript 1 refers to the entering conditions and subscript 2 to the leaving conditions. a) With the intermediate pressures chosen so that the total work of compression is a minimum, what is the minimum work required to compress 1 kg of air, assuming that the compressions are reversible and adiabatic? b) What are the intermediate pressures that result in this minimum work of compression? c) Discuss the relative energy consumption by each compressor and the progression of the pressure through the three compressors.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

assuming that mass = 2150 kg K = 80.98 N/mm C =21.19 N/mm.
1-A linear reservoir (k= 350 md, q = 22%) is 23000 ft long, 3200 ft wide, 65 ft thick and is perfectly horizontal. Oil (p = 55 Ib/fi, u 2.1 cP) enters the reservoir from one end at a pressure of 2940 psi, and it is produced from a well on the other end (see sketch below) at 880 psi pressure. If the well is 12 inches in diameter, compute the steady-state production rate of oil in bbl/d. Hints: a. The flow is lincar in the first 21400 ft then becomes radial in the last 1600 fl. b. Only the right-hand half of the well is draining (producing) oil.
1000 cm^3 of air at an initial pressure of 1.10 × 10^5 Pa and temperature of 300 K undergoes the following changes: heat the air at constant pressureuntil its temperature reaches 390 K and then compress the air isothermallyuntil it returns to the initial volume of 1000 cm3and finally allow the air to cool so that its final pressure is 1.10 × 10^5 Pa. i. Draw a P-V graph to represent the changes undergone by the air ii. Calculate the maximum volume of the air. iii. What is the maximum pressure of the air? iv. State how the net work done on the air for the whole process can bedetermined
The two following 2 energy level systems (E; = 0 & E; = 1) are brought into thermal contact: System A: 8 distinguishable particles; UA = 4 System B: 4 distinguishable particles; UB = 1 If a single unit of energy transfers from System A to System B, what is the final Wtot for the combined system?
Completely solve and box the final answer. Write legibly Determine the mass flow rate of steam through a nozzle having isentropic flow through it. Steam enters the nozzle at 10 bar, 500°C, and leaves at 6 bar. The cross-section area at the exit of the nozzle is 20 cm2. The velocity of steam entering the nozzle may be considered negligible. [Ans. 2.2 kg/s] Note: Please don't copy the answer/solution from the internet, I need a more in-depth solution for this problem. Thank you
number 1 A food product containing 80% moisture content is being frozen. Estimate the specific heat of the product at -8 ° C when 80% of the water is frozen. The specific heat of the dry product is 2 kJ / (kg ° C). It is assumed that the specific heat of water at -10 ° C is the same as the specific heat of water at 0 ° C, and that the specific heat of ice follows the function Cp es = 0.0062 T Frozen + 2.0649. Cp of frozen product = kJ / kg ° C.
(Q5] (a) The chamber contains 0.05 m' of ideal gas at a pressure of 20 KPa. The gas is subjected to an isothermal compression. until pressure reaches to 30 KPa. After that the gas is subjected to compression according to PV 2-const until pressure reaches to 40 KPa then an isobaric compression is done till volume reaches 0.005 m3. Assume that no loss in gas during the whole process : I- Sketch the process on P-V diagram and P-T diagram II- Find the work done during the entire process and temperature at end of each process.. gas
70 Energy (Joule) ☎ 8 8 8 8 8 8 50 30 10 o S2FRT820 $2FRT730 AS2FRT650 S2HT940 o $2HT1150 0 -200 -150 S2FRT820 O -100 + S2HT940 A -50 0 Temperature (°C) O O S2FRT730 ... S2FRT650 $2HT1150 50 100 The figure shown corresponds to the absorbed energy of different ferritic steels in a temperature range of 1. What is the ductile-brittle transition temperature of S2FRT730 steel? 2. If a component will work at -50°C, what materials (from those shown) would you use to manufacture it? EXPLAIN YOUR ANSWER.
Solve the following application problem: The model s(t) = -16?2 + 5? + 3 describes the height(in feet) of a diver at time ? is measured in seconds. Find the velocity of the diver when the diver hits the water.
number 1 A food product containing 75% moisture content is being frozen. Estimate the specific heat of the product at -10° C when 85% of the water is frozen. The specific heat of the dry product is 2 kJ / (kg ° C). It is assumed that the specific heat of water at -10 ° C is the same as the specific heat of water at 0 ° C, and that the specific heat of ice follows the function Cp es = 0.0062 T Frozen + 2.0649. Cp of frozen product = kJ / kg ° C.
You have a wind turbine with a maximum power rating of 5 MW available for use in a wind farm. This turbine can operate in winds ranging from a minimum speed of 2 m/s up to a maximum wind speed of 10 m/s (which is when the turbine produces its maximum power). You have two possible sites available: the first site has a steady wind that always blows at 6 m/s. At the second site, the wind blows at 1 m/s for 50% of the time, and at 10 m/s for the other 50% of the time. a. If maximizing the peak power production is the most important consideration, which site should you choose? What will be the maximum power for a single turbine? b. If maximizing the average power production is the most important consideration, which site should you choose? What would be this average power for a single turbine?
Problem #2: A velocity distribution is given as V = Please calculate the work flux (Iv) associated with molecular motions. -bx8,-byô, + bz8, where b is a constant and b‡0.