shows two pulleys are fixed to the shaft and supported by the roller bearing at points A and B. Assume the belt tension on the loose side of the 0.3-m radius pulley is 15 percent of the tension on the tight side of 60 kN. The shaft is rotating with a speed of 600 rev/min in this application. If the roller bearing is expected to operate for 1200 hours and the reliability for this bearing set is 0.90, select a suitable bearing to be installed at points A and B. Assume application factor of unity. 80 KN 40 kN 1 m 1m C₁ T 1m 0.3 m B 60 kN

shows two pulleys are fixed to the shaft and supported by the roller bearing at points A and B. Assume the belt tension on the loose side of the 0.3-m radius pulley is 15 percent of the tension on the tight side of 60 kN. The shaft is rotating with a speed of 600 rev/min in this application. If the roller bearing is expected to operate for 1200 hours and the reliability for this bearing set is 0.90, select a suitable bearing to be installed at points A and B. Assume application factor of unity. 80 KN 40 kN 1 m 1m C₁ T 1m 0.3 m B 60 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows a 16T 20' straight bevel pinion driving a 32T gear, and the location of the bearing centerlines. Pinion shaft a receives 2.5 hp at 243 rev/min. Determine the bearing reactions at A and B if A is to take both radial and thrust loads.
Q1/ A 6-in-wide polyamide F-1 flat belt is used to connect a 2-in-diameter pulley to drive a larger pulley with an angular velocity ratio of 0.5. The center-to-center distance is 9 ft. The angular speed of the small pulley is 1750 rev/min as it delivers 2 hp. The service is such that a service factor Ks of 1.25 is appropriate. (a) Find Fc, Fi, Fla, and F2. (b) Find Ha, nfs, and belt length. (c) Find the dip.
Deep groove ball bearings are most widely used bearing type and suitable for many different industries. A 02-series single-row deep-groove ball bearing with a 30-mm bore is loaded with a 2-kN axial load and a 5-KN radial load. The inner ring rotates at 400 rev/min. a. Determine the equivalent radial load that will be experienced by this particular bearing. b. Determine the predicted life (in revolutions) that this bearing could be expected to give in this application with a 99 percent reliability.
A steel spur pinion has 16 teeth cut on the 20° full-depth system with a module of 8 mm and a face width of 90 mm. The pinion rotates at 150 rev/min and transmits 6 kW to the mating steel gear. What is the bending stress?
Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels connecting A and C having a module of 2 mm and those connecting C and B have a module of 3.5 mm. Speed of B is less than 1/10th that of A. If the two pinions have each 20 teeth, find suitable number of teeth for the wheels to improve the performance of the mechanism, the actual velocity ratio, and corresponding center distance of shafts C and A.
A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum. The 48V DC motor selected has a no-load angular velocity of 800 RPM and a stall torque of 500 inch-pounds. A gearbox has been designed to spin the drum as quickly as possible. Assume that there are no friction losses in this system. The drum is driven by a 72-tooth gear with a diametral pitch of P=8, and is 3D printed such that it has a yield strength in shear of τy = 2500 psi. Assuming that the entire output torque required to turn the drum is produced by the force on one tooth, and that the gear tooth would fail by being sheared off at the pitch circle, determine the required gear face width, b, for a factor of safety of 3. Note that circular tooth thickness, t, at the pitch circle is π / (2P). Repeat for a gear made out of 6061 Aluminum (σy = 35 ksi, τy = 20 ksi). Only do the part for the 6061 gear do not do it for the 3D printed gear
Machine design A 60-hp four-cylinder internal combustion engine is used to drive a medium-shock brickmaking machine under a schedule of two shifts per day. The drive consists of two 26-in sheaves spaced about 12 ft apart, with a sheave speed of 400 rev/min. Select a Gates Rubber V-belt arrangement. Find the factor of safety, and estimate the life in passes and hours?
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
A steel shaft of 2.5 inch diameter rotates at 500 rev/min and transmits 120 hp through a gear. Select an appropriate square key for the gear, while the key material having yield strength of 60 kpsi. Assume a factor of safety of 2.0.. Draw sketch and show all calculations.
A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the systemhas a diameter 150 mm and rotates at 200 rev/min. The grove angle is 40° and thecoefficient of friction between the belt and pulley is 0·3.(a) If the maximum tension in any one belt is limited to 800 N and the angle of lap is135°, determine the number of belts required. (b) Determine also, the initial pre-tension required in the belt.
Determine the maximum permissible angle between the shaft axes of osuniversal joint if the drivix cshaft rotates and the total fluctuation ofe meed does not exceed 60 rpm. Also, find then m mum and the minimum speeds of the driven shaft. at 800
Question 1: The figure shows a 16T 20° straight bevel pinion driving a 32T gear, and the location of the bearing centerlines. Pinion shaft a receives 2.5 hp at 248 rev/min. Determine the bearing reactions at A and B if A is to take both radial and thrust loads. On-Screen Keyboard Esc 1 3. 4 5 6.