Server reply (UDP). How does the networked application running on a server know the client IP address and the port number to reply to in response to a received datagram? As the result of performing the accept () statement, the server has created a new socket that is bound to that specific client, and so sending into this new socket (without explicitly specifying the client IP address and port number) is sufficient to ensure that the sent data will be addressed to the correct client.

Server reply (UDP). How does the networked application running on a server know the client IP address and the port number to reply to in response to a received datagram? As the result of performing the accept () statement, the server has created a new socket that is bound to that specific client, and so sending into this new socket (without explicitly specifying the client IP address and port number) is sufficient to ensure that the sent data will be addressed to the correct client.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

2- Client is connecting a server via TCP to get an object from HTTP Server. Skitch the TCPwindow connection including (establishing connection, the request from client, the response byserver, sending data from server side and closing the connection).Knowing that:1- Get request from the HTTP 1.1 server is 259 bytes.2- Response from the server is 223 bytes.3- Data size requested is 900 bytes.
Computer Science Networks and should be done in C language. Create a UDP client and server program that not only is able to locally transfer files but it gives the client the ability to send multiple copies of the file to multiple servers. Once the server program is initiated, it waits until it receives client packets. It then reads and saves the payload of the packets. The client reads a file from the disk and sends it to each server over a UDP socket by breaking the file up into mtu-byte sized packets. Client needs to be concurrent in sending the packets to all of the servers using threads
In IEEE 802.11, two-way communication is used to authenticate an open system. In order to authenticate the client, the server must give the station ID (typically the MAC address). Response to the client's previous request is either a successful or failed authentication response from the access point/router. An error may arise if, for example, an AP/router configuration does not include the client's MAC address.In what ways is it advantageous to use this kind of authentication scheme?In what ways does this authentication technique have security vulnerabilities that might be mitigated?
UDP Echo ApplicationA UDP Echo program is a simple network application that demonstrates the basicprinciples of UDP communication. In this program, a server listens for incoming UDPpackets from clients, and when it receives a packet, it echoes (sends back) the samepacket to the client. The client sends a message to the server, and the server returns thesame message. It's often used for testing network connectivity and understanding thefundamentals of UDP communication. (Answer the following question using python) Implement both the server and client components of this UDP Echo program whileadhering to the features outlined below. Please ensure that your implementation followsgood coding practices and provides clear prompts and feedback to the user, making ituser-friendly and robust. Please refer to the class example to guide your implementation. 1) UDP Echo Server Receiving and Displaying Messages: The UDP Echo server should be able toreceive messages sent by clients. For each…
SMTP (Simple Mail Transfer Protocol) is the standard protocol for transferring mail between hosts. A TCP connection is set up between a user agent and a server program. The server listens on TCP port 25 for incoming connection requests. The user end of the connection is on a TCP port number above 1023. You have defined the packet filter rule set shown in the table below. These rules permit and/or deny inbound and outbound traffic between the user agent and the mail server. Describe the purpose of each packet filter rule in the table. Rule Direction Source Address Destination Address Protocol Destination Port Action A2 In External Internal TCP 25 Permit B2 Out Internal External TCP > 1023 Permit C2 Out Internal External TCP 25 Permit D2 In External Internal TCP > 1023 Permit E2 Either Any Any Any Any Deny
Q1) How many RTTs are there from when a client first contacts an email server (by initiating a TCP session) to when the client can begin sending the email message itself - that is following all initial TCP or SMTP handshaking required? Recall the figure below from our class notes: "client" SMTP server initiate TCP connection RTT TCP connection initiated SMTP handshaking SMTP transfers "server" SMTP server time 220 HELO 250 Hello
Obtain the HTTP/1.1 specification (RFC 2616). Answer the following questions: a. Explain the mechanism used for signaling between the client and server to indicate that a persistent connection is being closed. Can the client, the server, or both signal the close of a connection? b. What encryption services are provided by HTTP? c. Can a client open three or more simultaneous connections with a given server? d. Either a server or a client may close a transport connection between them if either one detects the connection has been idle for some time. Is it pos- sible that one side starts closing a connection while the other side is transmitting data via this connection? Explain.
Q: Imagine a Web server that maintains a table in which client IP addresses are mapped to the most recently accessed Web pages. When a client connects to the server, the server looks up the client in its table, and if found, returns the registered page. Is this server stateful or stateless?
A socket is one endpoint of a two-way communication link between two programs running on the network. A socket is bound to a port number so that the TCP layer can identify the application that data is destined to be sent to. An endpoint is a combination of an IP address and a port number.Discuss about the different types of socket calls using in TCP &UDP.
Obtain the HTTP/1.1 specification (RFC 2616). Answer the following questions: a. Explain the mechanism used for signaling between the client and server to indicate that a persistent connection is being closed. Can the client, the server, or both signal the close of a connection? b. What encryption services are provided by HTTP? c. Can a client open three or more simultaneous connections with a given server? d. Either a server or a client may close a transport connection between them if either one detects the connection has been idle for some time. Is it possible that one side starts closing a connection while the other side is transmitting data via this connection? Explain.
Computer Science Java You are to create a direct messenger program. In particular, the program will perform as follows: It must behave as either a client or a server, depending on the command line arguments supplied when started. Specifically, the -l option will direct the program to listen for connections, thereby acting as a server. If the -l option is not present on the command line, your program will connect to a server, thereby acting as a client. The port number must also be supplied as a command line argument. Although your messenger may be hard-coded to connect only to localhost when acting as a client, you may include a server address on the command line as well, thereby permitting your messenger to connect between hosts. The -l option, if used, should be placed immediately after the name of the program and before the port number and server address arguments. Once the client and server messengers are connected, either end can send text messages to the other end. Messages must…
Refer the configuration below, IT Router is configured as follows: IT (config)#enable secret cisco IT (config)#line con 0 IT (config-line)#password class IT (config-line)#login IT (config-line)#exit IT(config)#interface vty 0 15 IT (config-line)#password class IT (config-line)#no shutdown IT (config-line)#end IT#copy run start From the above configuration, identify the mistakes or missing in the configuration and write the correct commands.