Replace the three forces which act on the bent bar by a force-couple system at the support point A. Then determine the x-intercept of the line of action of the stand-alone resultant force R. y 2500 lb 4- 1200 lb •A 30° C. 2' •D E 2'. 800 lb 3'

Replace the three forces which act on the bent bar by a force-couple system at the support point A. Then determine the x-intercept of the line of action of the stand-alone resultant force R. y 2500 lb 4- 1200 lb •A 30° C. 2' •D E 2'. 800 lb 3'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 20 m to m A 4000N (5 m 10 m O Determine the Force of member AB. 2 AC. AD.

Q: Represent the resultant of the force system acting on the pipe assembly by a single force R at B and…

Q: Express and identify the resultant of the two forces and one couple shown acting on the shaft angled…

Q: 4m 3 m 6 m 3 m F 60KN 85KN

Q: Replace the three forces and one couple which act on the bar by a force-couple system at the support…

A: Equilibrium of horizontal forces, ∑Fx=0Fx=5cos45°=3.54 kN Equilibrium of vertical forces,…

Q: B BI .n N, F₁ = i N, Ft= i

Q: The bar ABC of negligible weight is supported by a pin at A and a rope that runs around the small…

A: Step 1

Q: 1380 N 800 N 1.8m1.8m A 25° 1.5m 2.1m

Q: 1.in. dia 8 24 lb/in. 12 ft 2 in. A 1.0 in. В 3 ft

Q: The rigid beam of negligible weight is supported by a pin at O and two vertical rods. Determine the…

A: Given- l1=3ftl2=10ftA1=2in2E1=12×106A2=0.5 in2E2=29×106 Psi The diagram is given below

Q: Express and identify the resultant of the two forces and one couple shown acting on the shaft angled…

Q: Determine the magnitude of the pin force at A. Assume W = 660 lb, a = 2.8 ft, b = 2.0 ft, r = 7 in.…

Q: Express and identify the resultant of the two forces and one couple shown acting on the shaft angled…

A: M= 10782.8 î + 0 j + 4278.86 k

Q: A rod has a radius of 4m. Determine the smallest force F that must be applied along the rope in…

A: In order to determine the force which will cause failure in curved rod we will take total moment…

Q: Find the value of Ely at the position midway between the supports. 600 N/m B A D 2m 3m 1m

Q: A 45° P

Q: A 29-lb force is required to operate the foot pedal. Determine the tension, 'T' in the connecting…

Q: Express and identify the resultant of the two forces and one couple shown acting on the shaft angled…

A: Given data: F=470 lb M=300 lb-ft a=9 in b=22 in It is required to find resultant of two forces and…

Q: The force P is applied to (a) the 60-lb block and (b) the 100-lb block. For each case, determine the…

A: Given:- force P is applied to block as shown below;

Q: The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After applying…

A: ASKED: To determine- (1) maximum normal stress developed in each rod (2) Horizontal displacement of…

Q: Problem 3: Determine the unstretched length of spring AC if a force p = 80 lb causes the angle 0 =…

Q: Determine the tension developed in wire CB required for equilib Kg cylinder take angle 0 =40…

Q: Replace the force and couple system shown by anequivalent resultant force and couple moment acting…

A: Free body diagram with all representation of values obtained in answer

Q: 1380 N 800 N „1.8m1.8m A 25• 1.5 m 2.1m

Q: prevent a load (weight W) from falling downwards. The drum can rotate without friction about point…

Q: Replace the three forces acting on the bent pipe by a single equivalent force R. Specify the…

A: When the force is said to be equivalent the two forces have the same magnitude and the direction and…

Q: Determine the force (written as a vector) which BC exerts on member AB (a) if the 810-N load is…

A: Given data: P=810N∅=22°a)if the 810-N load is applied to the center of member…

Q: determine the stiffness k of each spring so that the 30-N force causes the bar to tip angle = 15…

Q: Determine the magnitude of the pin force at A. Assume W = 765 lb, a = 3.8 ft, b = 2.9 ft, r = 9 in.…

Q: 300 lb 30° 224 lb 361 lb

Q: Determine the magnitude of the pin force at A. Assume W = 845 lb, a = 3.0 ft, b = 2.0 ft, r = 9 in.…

A: We have to find the value of magnitude of pin force at A. Given data is W = 845 lb, a = 3.0ft, b 2.0…

Q: The rigid beam of negligible weight is supported by a pin at O and two vertical rods. Determine the…

A: Given: The area of the bronze rod is 2 in2. The modulus of elasticity of the bronze rod is 12 x 106…

Q: Determine the magnitude of the pin force at A. Assume W = 640 Ib, a = 3.5 ft, b = 2.6 ft, r = 8 in.…

A: Step 1

Q: / The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After…

Q: Determine the magnitude of the pin force at A. Assume W = 530 Ib, a = 3.6 ft, b = 2.9 ft, r = 9 in.…

Q: If the 5kg block is suspended from the pulley B and the sag of the cord is d 0.15 m. Draw (FBD) and…

Q: determine the stiffness k of each spring so that the 30-N force causes the bar to tip angle = 15…

Q: A rigid bar ABCD is hinged at point B and supportee py two springs at A and D. The spring at A and D…

Q: Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA.…

Q: Express and identify the resultant of the two forces and one couple shown acting on the shaft angled…

Q: Determine the resultant of the three forces acting on the pulley shown

A: To find resultant of force

Q: 4 kN 3. Three forces act on the plate. Determine the sum of the moments of the three forces about…

Q: Determine thepoint of inflection (in feet) measured from the left end. * Your answer Derive the…

Q: 2.16 Pins at A and D, and a steel rod at B. support the rigid bars ABC and CD. A roller connection…

Q: Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA.…

Q: Determine the unstretched length of spring AC if aforce P = 80 lb causes the angle θ = 60° for…

A: Given: Force, P is 90 kN. θ=600 The length of the chord, lAB is 2ft. Spring constant, k =50 lbft The…

Q: DETERMINE FORCE (N) OF MEMBER EG in the truss shown. F1 = 214 N F2 = 876 N F3 = 435 N a = 38 degree…

Q: b) A block of weight W, holds a ring anchor bolt to which are fastened two wires as shown; angle is…

A: Hear the following equations for the resultant force and Angle of resultant force with horizontal…

Q: C B A 45° 30° W

Q: Вronze A= 2 in.? E = 12 x 10° psi- Steel 10 ft A = 0.5 in.? E= 29 x 10° psi 3 ft 8 ft 50 kips

A: Take moment about support: ∑M=03Pbr+12Psteel=8×50000=400000 ......1…

Concept explainers

Pressure and Stress

Question

Replace the three forces which act on the bent bar
by a force-couple system at the support point A.
Then determine the x-intercept of the line of action
of the stand-alone resultant force R.
2500 lb
1200 lb
•A
B•
30°
D
E
800 lb
إضافة ملف

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2D force systems 1- Determine the resultant R of the two forces shown by (a) applying the parallelogram rule for yectoraddition and (b) summing scalar components. Dr Hazim Umran AEwan Ans (872 N 60 400 N 2- At what angle e must the 800-N forco the two forces has a angle
5 نقاط Q1 - B: Determine the force in arm CD 0.3 m 0.3 m 200 N B 0.6 m 0.3 m 1.2 m 103.1 N O 110.2 N 150 N 70 N 50 N O
Q2/ Determine the resultant moment of the forces about point B F=400N 100 N D 30° A 45° 0.3 m B Iroon tozm t 100 N 0.4 m 0.2r
3. Determine the resultant of the force system. Indicate where the line of action of the resultant intersects the line AB. 900 N 125mm 1730 N 75mm 200mm 100mmT100mm 450 N ERSITY
JON | 20 N 10N E: 15N Com 8m 4m Em 4m From the figure above, determine the: A. Resultant reaction at supports B. All the member forces (AE, AC, CF, EC, EF, FG, GB, BD, DF, DG) /
Handle forces F₁ = {41-45-10k) N and F,- (2j-6k) N are applied to the electric drill(Ejgure 1) Replace this force system by an equivalent resultant force Fg and couple moment M, acting at point ( Figure 615 1025m 13m 1 of 1 Y Part A Determine the equivalent resultant force Fa Enter the z, y, and a components of the force separated by commas. FR Fay F. 4.00-2.00-160 N Previous Answers Correct Part 8 Determine the couple moment Ma Enter the z. y. and components of the moment separated by commas. ΜΕ ΑΣΦ M M M 2.1,0.3,-0.6 Submit Pous Answers Be Aw vec 4 N-m
acting at point O. 100 N y 600 mm 90 N Replace the three forces with an equivalent force-couple system, with the force 40 N-m 400 mm 1300 mm 800 mm 50 N 500 mm 40°
Determine the resultant of the force system. Indicate where the line of action of the resultant intersects the line AB. 900 N 75mm 125mm 1730 N 75mm 200mm 100mm100mm 450 N DIFICAL
ホーaxis GON 554° 300 Find the t-component of the Rsulteant OF the force sysem shown.
The two forces acting on the handles of the pipe wrenches constitute a couple 'M'. Express the couple as a vector Z 150 N 250 mm B 150 N OM -75i+22.5j N.m OM -75i+2.5j N.m OM -85i+22.5j N.m 150 mm 250 mm
Question Bank - Friction Determine the range of P for which the system of two blocks will be in equilibrium. Friction is negligible except for the surface under block B. 30° 120 N P. 80 N H, = 0.2- Technelagy Drien by fanovation Tip: Draw the Free Body Diagram Determine force P [ Select ] Determine N-force at gound to block B [ Select ] Detemine N-force between surfaces of A and B [Select ] Determine the N-force between the wall and block A [ Select]
Replace the three forces and one couple which act on the bar by a force-couple system at the support point A. Then determine the x-intercept of the line of action of the stand-alone resultant force R. 10 kN 5 kN 3 kN 45° В 10 kN.m 2 m 3 m 2 m 2 m