QUESTION 1A batter swings a 0.9 m long bat. Assume the bat has a mass of 0.6 kg the bat rotates at 3 rad/s. The kinetic energy of the bat isJ.1ML3(Hint: Approximate the bat by a rod, or a long thin cylinder, and use I=-ML2 for the rotational inertia of a rod of mass M andlength L rotating around its end perpendicular to its length)

0.9m longmass=0.6kgrotates=3 rad/secFINDKinetic energy of the bat is

QUESTION 1 A batter swings a 0.9 m long bat. Assume the bat has a mass of 0.6 kg the bat rotates at 3 rad/s. The kinetic energy of the bat is, J. 1 3 (Hint: Approximate the bat by a rod, or a long thin cylinder, and use I=-ML2 for the rotational inertia of a rod of mass M and length L rotating around its end perpendicular to its length)

QUESTION 1 A batter swings a 0.9 m long bat. Assume the bat has a mass of 0.6 kg the bat rotates at 3 rad/s. The kinetic energy of the bat is, J. 1 3 (Hint: Approximate the bat by a rod, or a long thin cylinder, and use I=-ML2 for the rotational inertia of a rod of mass M and length L rotating around its end perpendicular to its length)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitudes of F1, F2, and F3 for equilibrium of the particle.
Determine the angular momentum Hp of each of the two particles about point P. Use a scalar solution. Take that mA = 2.0 kg and mp = 1.2 kg. (Figure 1) Figure A 15 m/s MA y 0 -2m- 30° 10 m/s B 5 m 1.5 m m' 4 m | mB 4 m X < 1 of 1 Part A Hp of the particle A about point P. Express your answer to three significant figures and include the appropriate units. +(HA)P= Value Submit Part B μA Submit Request Answer Provide Feedback Hp of the particle B about point P. Express your answer to three significant figures and include the appropriate units. HÅ +(HB)P= Value | Units Request Answer ? Units ?
The particle of mass m = 2.3 kg is attached to the end of the light rigid bar of length L = 0.83 m. The system is released from rest while in the horizontal position shown, at which the torsional spring is undeflected. The bar is then observed to rotate 45° before stopping momentarily, (a) Determine the value of the torsional spring constant kr. (b) For this value of kr, determine the speed vof the particle when e = 25°. kT Part 1 Position 1 is the horizontal orientation shown in the figure. Position 2 is the orientation when e- 45. Find the kinetic energy in positions 1 and 2. Answers: T1- kg m²/s2 T2- kg m²/s? Answers: (a) ky = i Nem/rad (b) m/s
Find the following using the photo below. e. If a = 2 m/s2, determine v at s = 4 m if v = 3 m/s at s = 0.f. If a = 4 m/s2, determine s when t = 3 s if v = 2 m/s and s = 2 m when t = 0.g. When t = 0 the particle is at A. In four seconds it travels to B, then in another six seconds it travels to C. Determine the average velocity and the average speed. The origin of the coordinate is at O.
U.S. AB= 21 Bc = I • CALCULATE THE • MOMENT OF INERTIA REACTIONS A (30k OF THE 20K BEAM MEXICO 2.5K/FT 17 20 B
Find the magnitude and direction in X and Y of the motion of the joint at point C of the flat truss supporting a load of 1000 N as shown in the figure below. The value of E=210GPA for each member, the elements have a circular section with an external diameter of 75 mm and a thickness of 5 mm. Use the work and energy method. (In the picture it says 10 but it's 1000) E D B 1920 mm 1080 mm ION 810 mm 1440 mm
The rotor of an electric motor has an angular velocity of 4500 rpm when the load and power are cut off. The 75-kg rotor, which has a centroidal radius of gyration of 200 mm, then coasts to rest. Knowing that kinetic friction results in a couple of magnitude 4.5 N m⋅ exerted on the rotor, determine the number of revolutions that the rotor executes before coming to rest. DO NOT ROUND OFF IN THE SOLUTION. ROUND OFF ONLY IN 2 DECIMAL PLACE IN THE FINAL ANSWER
Ug Two similar round bars A and Bare each 30 cm long and loaded as shown in the given figure. The ratio of the energies stored by the bars A and B, is (Ignore self weight bars). 4P 2 cm 2 cm 10 cm 20 cm 4icm 20 cm 10 cm Bar A Bar B
A homogeneous disk with a radius of 9 in. is welded to a rod AG with a length of 18 in. and of negligible weight that is connected by a clevis to a vertical shaft AB. The rod and disk can rotate freely about a horizontal axis AC, and shaft AB can rotate freely about a vertical axis. Initially, rod AG is horizontal (0o= 90°) and has no angular velocity about AC. Knowing that the smallest value of 0 in the ensuing motion is 30°, determine (a) the initial angular velocity of shaft AB (b) its maximum angular velocity.
Cross-section of a beam 3) The rectangular tube cross-section of a beam, shown in the figure aside, is bent about a horizontal axis due to the bending moment of 899.5 Nm. Calculate the total force that is acting on the shaded portion of the cross-section of the beam. (Suggested time for solution is 25 minutes) 0.8cm C 4.6cm 0.8cm 3cm 0.8cm 0.8cm
Q4- The 3500-lb automishile shown in Fig. 3 travels diwn the 10 inclined nad at a speed of 20 . If the driver jams on the brakes, causing his whoels to lock, deternine how far s the tires skid on the at. The coefficient of kinetic frietion between the wheels and the rad is m05 200A Fig I Fig 2 Fig 3
In the figure particle 1 of charge +4e is above a floor by distance d1 = 2.70 mm and particle 2 of charge +8e is on the floor, at distance d2 = 6.60 mm horizontally from particle 1. What is the x component of the electrostatic force on particle 2 due to particle 1? di Number i Units