Given the two-dimensional velocity field V = 2 xi+5yj, where x is in cm, and V is in cm/s, what is the volumetric strain rate? O751 O 4 (cm-s)-1 x 4 (cm-s)-1 x+ 25 (cm-s)-1 y O 14 (cm-s)1 x QUESTION 8 If a steady flow of water enters a nozzle with an entry diameter of 8 cm at a speed of 20 cm/s, and leaves the nozzle with a speed of 120 cm/s, what is the exit diameter of the nozzle?

Given the two-dimensional velocity field V = 2 xi+5yj, where x is in cm, and V is in cm/s, what is the volumetric strain rate? O751 O 4 (cm-s)-1 x 4 (cm-s)-1 x+ 25 (cm-s)-1 y O 14 (cm-s)1 x QUESTION 8 If a steady flow of water enters a nozzle with an entry diameter of 8 cm at a speed of 20 cm/s, and leaves the nozzle with a speed of 120 cm/s, what is the exit diameter of the nozzle?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 6 of 11 -/10 E View Policies Current Attempt in Progress The stresses shown in the figure act at a point on the free surface of a machine component. If o= 45 MPa in the direction shown, determine the normal stress oy at the point. 27 MPa 30° 50 MPa O -16.3 MPa O -19.5 MPa O-22.8 MPa O-17.2 MPa O -20.5 MPa Attempts: 0 of 1 used Submit Answer Save for Later
A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the stress in a fiber 50mm from the top of the beam at point B. 50kN A 20 купи RI B 2M X 30KN/M TITT. 4m 20 km. ITTJ 2m + <
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the stress in a fiber 50mm from the top of the beam at point B. sokn B 30 kN/m 20 kn/m 20 km 2m 2m 4m R₁ * D +
200KN A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of each material are shown in the figure. A fixed support is rigidly attached to the right end of the bronze rod. Determine the stress each section in kPa. Aluminum Steel D=28mm D=20mm 20KN Bronze D=25mm 150KN
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm
VECHANICS OF D. 5. 73.8% THERMAL STRESS Steel Rod d = 20 mm L = 5 m E = 200 GPa a = 11.70 µm/(m-°C) p = 8,000 kg/m³ 1. A steel rod is positioned vertically as shown in the figure. It is fixed at one end and unsupported at the other end. An external force (F = 800 N) is applied to the free end of the rod the same time when the temperature is raised by 25 C. Assume that all deformations will happen at the same time, compute the stress developed in the steel rod if the gap between the free end of the steel rod and the ground is 0.20 mm. %3D GAP
A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂ bonded to an 80-mm-long hollow rubber cylinder with a modulus of rigidity G = 10.93 MPa. Determine the required value of the ratio R2/R1 if a force P = 13 kN is to cause a 2-mm deformation of rod A. B R₁ R₂ .. 80 mm The required value of the ratio R2/R₁ is 1.422
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E= 70000 MPa. The length of each bars are follow: B1 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B1 in MPа. 35KN B1 B2 ВЗ 10KN 15KN 30KN A 218.75 В 125 (c) 62.5 31.25
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Material Properties Material Area(mm2) E (GPa) Normal Stress(MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140 Aluminum 3P Bronze Steel 2P 4P - 0.6 m →- 1.0 m 0.8 m
Example 1.2 (a) A 25 mm diameter bar is subjected to an axial tensile load of 100 kN. Under the action of this load a 200 mm gauge length is found to extend 0.19 x 10-3 mm. Determine the modulus of elasticity for the bar material. (b) If, in order to reduce weight whilst keeping the external diameter constant, the bar is bored axially to produce a cylinder of uniform thickness, what is the maximum diameter of bore possible given that the maximum allowable stress is 240 MN/m2? The load can be assumed to remain constant at 100 kN. (c) What will be the change in the outside diameter of the bar under the limiting stress quoted in (b)? (E = 210 GN/m² and v = 0.3).
Determine the stress in each section of the bar shown in the Figure when subjected to an axial tensile load of 25 kN. The central section is 30 mm square cross-section; the other portions are of circular section; their diameters being indicated. What will be the total elongation of the bar? For the bar material E=210N/mm². 250mm 100mm, 400mm 25 KN 2 O 25 KN 30mm 20mm 15mm