Please answer clearly (d)Figure Q1(d) shows a circuit that has been developed for an electroniccommunication project. An amplifier with gain of 3.35 dB was utilized tocompensate the signal loss by a voltage divider circuit.(i)Determine the value of resistor R3, if resistor Rj is 4702.This circuit is connected with another amplifier with t gain of 20dB. Estimate the output voltage if the input signal is 10 mV(ii)R1R2Figure Q1(d): Electronic communication circuit

From given configuration calculate unknown resistance R2. Gain of the series connected amplifier is…

Figure Q1(d) shows a circuit that has been developed for an electronic communication project. An amplifier with gain of 3.35 dB was utilized to compensate the signal loss by a voltage divider circuit. (d) (i) Determine the value of resistor R3, if resistor R, is 47092. (ii) This circuit is connected with another amplifier with t gain of 20 dB. Estimate the output voltage if the input signal is 10 mV R1 R2 Figure Q1(d): Electronic communication circuit

Figure Q1(d) shows a circuit that has been developed for an electronic communication project. An amplifier with gain of 3.35 dB was utilized to compensate the signal loss by a voltage divider circuit. (d) (i) Determine the value of resistor R3, if resistor R, is 47092. (ii) This circuit is connected with another amplifier with t gain of 20 dB. Estimate the output voltage if the input signal is 10 mV R1 R2 Figure Q1(d): Electronic communication circuit

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the output impedance for small-signal equivalent circuit. (R1=10 k ohm, r0, =10 k ohm)
The term duty cycle refers to the amount of time a signal is complete cycle. A. off compared to the period of one B. on The output voltage of op-amp is positive saturation, when the voltage applied to the input is greater than the input. A. inverting B. noninverting A square wave that is 20V at its high state and OV when it is off will produce an average DC when its duty cycle is 75%. Formula: VOUT = Duty Cycle * Peak voltage voltage of A. 7.5V B. 10V C. 15V
Figure 1(a) shows a series fed class A amplifier circuit. In order to achieve the maximum efficiency, the Q point must be located at the center of the DC load line as shown in Figure 1(b). This generates the maximum output current swing of Icmax (p – p) RC and the maximum output voltage swing is VCEmax(p – p) = Vcc Assume that the maximum input de power is (1 Vcc Pimax(dc) = Vcc!cQ(max)=Vcc \2° Rc. 2Rc Find the maximum efficiency, 7 of this circuit.
1. For the following circuit assume re = 30.6 1 a. Draw the small signal equivalent circuit. b. Find the input impedance. c. Find output impedance. d. Find the voltage gain. e. Find the current gain. 4.72 10F
As a maintenance engineer in a semiconductor company, you are given a task to replace the current version of dc-biasing circuit for a faulty tester machine. This dc-biasing circuit used an n-channel JFET as shown in Figure 2. Re-design a new dc-biasing circuit using an n-channel D-MOSFET that can produce a similar output current, IDQ as the previous circuit. Your tasks are: (i) Calculate the operating point (IDQ and VGSQ) of the dc-biasing circuit in Figure 2. Then sketch the JFET network transfer curve (ID and VGS). (ii) Without changing the circuit configuration, calculate the values of source resistor, RS and RB to achieve this objective. Determine the commercial value of the new RS and RB.  For cost reduction reason, the values of RD, RA and VDD should be maintained.  The chosen D-MOSFET has a maximum drain current of 8 mA and gate-source cutoff voltage of – 15V.  The new RS value should be 3 times larger than the old RS used in the JFET network to compensate for the high…
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?
Q1:-Design and connect a subtractor operation amplifier circuit if the R1=R2=R3=Rf and V1=2V, V2=5V, draw the circuit with all details and record the measurement of the output voltage.
(2-d) Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier.
6) Consider the following multistage amplifier. Draw the corresponding small signal model. Label, Vin, Vo1 and Vo. Do NOT make any approximations. Do NOT perform small signal analysis with this model. Just draw the small signal model. Show your work! Vin Vcc malli Q1 Re1 Vo1 Vcc ww1. Rc2 Q2 Re2 Vo
Q.) Figure below divider bras amplifier Circuit. Givent the model Parameter : gm = 5o mS emitter (CE) Voltage BJT hibrid- TT Shows a Common riT: 6 Kr and to %3D : 00 +Vc. RI C2 Tooks touf RL Vo ihe 200 RE TCE Vs 20 a Draw the Ac eQuivalent at low Freauency Circuit Zi and b.) Determine inPut impedance at mid FreaUincy OutPut imPedance Z0 c.) Calculafe two low Cut -oFF FreQuen Cies FLC1 and FLC2 Ci and E2 respectively Such as due to the exterda al capacitors
Consider the circuit of Figure 1, with a periodic square signal voltage source at a frequency f = 500 [Hz], consider R = 1600 [22]. Solve the circuit and plot on graph paper (minimum 10 values between 0 and 2 milliseconds) the total current response, taking into account the source Vin = 24 [Vp]. Note: identify in the graph maximum and minimum points of the total current response. Vin CH1 L m 160 mH, 4 Q CH2 REF Figure 1. Series RL circuit. Note: to do by differential equations and not to use laplace
Write the expression for the output voltage of a balanced modulator