Figure below shows a rotating shaft simply supported in ball bearings at A and D and loaded by a nonrotatingorce Fof 6.8 kN. Using ASTM "minimum" strengths, estimate the life of the part.6Ttd7 (a) Shaft drawing showing all dimensions in millimeters;all fillets 3-mm radius. The shaft rotates and the loadis stationary; material is machined from AISI 1050cold-drawn steel.(b) Bending moment diagram.

Answered: Image /qna-images/answer/f74fd94f-f0d0-426b-bd3e-df17b034cdc1.jpg

Figure below shows a rotating shaft simply supported in ball bearings at A and D and loaded by a nonr orce Fof 6.8 kN. Using ASTM "minimum" strengths, estimate the life of the part. ST d? (a) Shaft drawing showing all dimensions in millimeters; all fillets 3-mm radius. The shaft rotates and the load is stationary; material is machined from AISI 1050 cold-drawn steel. (b) Bending moment diagram.

Figure below shows a rotating shaft simply supported in ball bearings at A and D and loaded by a nonr orce Fof 6.8 kN. Using ASTM "minimum" strengths, estimate the life of the part. ST d? (a) Shaft drawing showing all dimensions in millimeters; all fillets 3-mm radius. The shaft rotates and the load is stationary; material is machined from AISI 1050 cold-drawn steel. (b) Bending moment diagram.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 1 TOLERANCE A solid steel shaft with a diameter of 130 mm must be press-fittd in a journal bearing (Figure 1) with an inlet and outet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing hlet diameter as the basic size. Outlet Bearing Inlet Joumal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.
QUESTION 10 Estimate the shaft diameter required to produce a critical speed of rotation of 638 rpm for a steel shaft of total length L= 44 in. that carries a center load of 111 lb as shown in the figure below. The shaft is located at C, as shown in Figures 1 and 3. Submit your answer in millimeters. Steel shaft H L
1) A shaft, mounted in bearings at A and D, holds pulleys at B and C. All forces shown represent belt pulls. The shaft is made from ASTM grade 25 cast iron (Sur-26 kpsi, Suc-97 kpsi). The application requires a safety factor of SF=2.8. What diameter should be used for the shaft? [Remember, cast iron is a brittle material and brittle materials use Modified Mohr Theory] 300 lb 6" D. 50 lb fe 8" D. 27 lb 360 lb D 7" 6°
1) A shaft, mounted in bearings at A and D, holds pulleys at B and C. All forces shown represent belt pulls. The shaft is made from ASTM grade 25 cast iron (Sur-26 kpsi, Suc-97 kpsi). The application requires a safety factor of SF=2.8. What diameter should be used for the shaft? [Remember, cast iron is a brittle material and brittle materials use Modified Mohr Theory] 300 lb 6" D. 50 lb B 8" D. 8" 27 lb 360 lb D €6-7
! Required information A 24-mm-diameter uniform steel shaft is 600 mm long between bearings. Take the value of acceleration due to gravity g to be 9.81 m/s2, the value of y for carbon steel to be 76.5 × 103 N-m-3, and the value of Eto be 207 x 10⁹ N/m². NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the critical speed of the shaft in rads/s? (You must provide an answer before moving to the next part.) The critical speed of the shaft is 847.5 rad/s.
A power transmission shaft is to carry a steady 30 horsepower while rotating at 1000 rpm. Specify a suitable diameter for the solid circular shaft if it is to be made from AISI 1020 cold-drawn steel. Use Appendix A-2 for preferred size.
Use the general shaft layout given and determine critical diameters of the shaft based on infinite fatigue life with a design factor of 1.5. Check for yielding. Check the slopes at the bearings for satisfaction of the recommended limits in Table 7-2. Assume that the deflections for the pulleys are not likely to be critical. 10 in 500 lbf 75 lbf 8-in dia. Bearing at O 10.0" 500 lb d 75 lb Material 1040 Q and T 18 in Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions in the belt at pulley Bare T₁ and T2, where T₁ is 15% of T2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 10-in dia. 12 in T₂ 8.0⁰ T₁ 18.0" 10.0" I B pulley diameter = 8.0" Sut 113 kpsi T2 T1 pulley diameter = 10.0" Sy 86 kpsi 12.0" Bearing at C Using the DE-Goodman criteria and a design factor of 1.5, calculate the diameter based on the shaft's loadings…
Use the general shaft layout given and determine critical diameters of the shaft based on infinite fatigue life with a design factor of 1.5. Check for yielding. Check the slopes at the bearings for satisfaction of the recommended limits in Table 7-2. Assume that the deflections for the pulleys are not likely to be critical. 500 lbf 75 lbf 8-in dia. Bearing at O 500 lb d 10.0" 75 lb Material 1040 Q and T 18 in Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions in the belt at pulley B are T₁ and T2, where T₁ is 15% of T2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 10-in dia. 12 in T₂ T₁ The mean torque is 0 lb-in. The alternating torque is 2125 lb-in. The mean moment is 0 lb-in. The alternating moment is 5000 lb-in. 18.0" pulley diameter = 8.0" Sut 113 kpsi 10.0 B T2 T1 pulley diameter = 10.0" Sy 86 kpsi 12.0"…
A power transmission shaft is to carry a steady 30 horsepower whilerotating at 1000 rpm. Specify a suitable diameter for the solid circular shaft if it is tobe made from AISI 1020 cold-drawn steel. Use Appendix A-2 for preferred size.
Mechanical design A shaft with the following data: 1- The pulley (A) is 1000 mm in diameter and weight 300N. 2- The gear (B) pitch diameter is 600mm and weight -250N. 3- The pulley is keyed to the shaft at 400mm to the left of left hand bearing. 4-the distance between bearing C and B is 1250 mm. 5- The power is 20 kW at 750 rpm. 6- Tension ratio T1 / T2-2.5 7- The shaft d.livers power to a gear placed horizontally in front, the pressure angel of gear is 20. 8- The allowable shear stress is 70N / mm, kt-2 and km- 1.5. Determine: the diameter of shaft
Compute the twisting and bending moments of the shaft (AISI 4140 steel) given the following parameters: Shaft length = 42 in Shaft diameter = 0.945 in Force = 245.25 N Torque = 79.71 Nm
Q2-a) determine the advantages of power screw. h b-A shaft is to transmit 50 KW at 1200 rpm.. The allowable shear stress of the shaft material is 60N/mm².Design a suitable ball bearing to support this shaft.(use bearing tables)