Fatigue angle in Failure (record number of cycles before failure) Large Metal Paperclip Small Metal Small Plastic Large Plastic Paperclip degrees Paperclip Paperclip 45° 90° 180° 270° Evaluate: 1. Which type of paperclip lasted the largest number of cycles before failure (small metal, large metal, small plastic, or large plastic)? 2. Which paperclip lasted the least number of cycles before failure? 3. Which angle (45°, 90°, 180°, and 270°) was associated with the fewest cycles before failure? 4. Give three reasons why different paperclips may break at different number of bends?

Fatigue angle in Failure (record number of cycles before failure) Large Metal Paperclip Small Metal Small Plastic Large Plastic Paperclip degrees Paperclip Paperclip 45° 90° 180° 270° Evaluate: 1. Which type of paperclip lasted the largest number of cycles before failure (small metal, large metal, small plastic, or large plastic)? 2. Which paperclip lasted the least number of cycles before failure? 3. Which angle (45°, 90°, 180°, and 270°) was associated with the fewest cycles before failure? 4. Give three reasons why different paperclips may break at different number of bends?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given the following stress-strain graph:a. is the modulus of elasticity of "A-514" greater, less or equal to the one of "A-572"?b. from the previous question, make an estimatio for both of them, check that the graphic comes in %c. If we were to test these materials in a universal tension equipment, which one would withstand more load?d. If we were to test these materials in a universal tension machine, which one would elongate the most before fracturing? would elongate the most before fracturing? e. Of the 6 materials shown, do any behave as brittle materials? f.
Mark the following points on an Engineering Stress-Strain curve. Plastic limitElastic limitFracture strengthYield strengthUltimate tensile strength
O A cylindrical rod made from an unknown metal is 350mm long and has a diameter of 10mm. The rod is subjected to a tensile load. It experiences only elastic deformation and elongates by less than 1.0mm under an applied load of 19,800N. Could any of the four metals listed in the table below could be the unknown metal? If so which ones and why? Material Modulus of Yield Ultimate Elasticity / GPa Strength / MPа Tensile Strength / MPа Aluminium 70 255 420 alloy Brass 100 345 420 Copper alloy Steel 110 250 290 207 450 550
10. A standard steel specimen of 0.504" diameter elongated 0.0125" in an 8" gage length during a test where it was subjected to a tensile force of 6249 lb. If the specimen's gage length was measured to be 8.0025" after the test was over, what was the permanent plastic deformation? What is the elastic deformation and what is the modulus of elasticity of that metal? r PL AE
Yield strength, ultimate tensile strength, linear coefficient of thermal expansion, modulus of elasticity (E), proportional limit, and rupture strength are all examples of mechanical properties of engineering materials. O True False A non-destructive test is any examination of an object in any manner which will not impair the future usefulness of the object. Non-destructive tests include: magnetic-particle, impacting testing, radiography, eddy current, and fluorescent-penetrant. O True O False One way to make a metal stronger is to increase the metal's grain size. O True O False --- OL T A metal that has a crystalline structure is called amorphous. O True O False
Content: Stress Analysis. Do you think it is possible for a material to have a high Modulus of Elasticity (at least 70 GPa) whilehaving a high tensile elongation (at least 40%)? Why or why not?
MECHANICAL PROPERTIES OF MATERIALS (stress and tensile stress) Does the electrical tape with the highest load mean that that material has the greatest ultimate or tensile strength? Why or why not?
o (MPa) 900 800 700 600 500 400 300 200 100 0 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 Question 1 Which ONE of the following descriptions is TRUE for this material? Its yield stress is approximately 720 MPa. It is a brittle material. It is a ductile material. Its ductility as a percentage elongation is approximately 0.6%. E
UeM Page 10 of 14 OUTCOMES- Discussion Answer ALL the questions: 1. A Charpy V-notch specimen is tested by the impact-testing machine. In the test, the 15 kg hammer of arm-length 120 cm (measured from the fulcrum to the point of impact) is raised to 90° and then released. i. What is the potential energy stored in the mass (hammer) when it hit the specimen, in J? i. After fracture of the specimen, the hammer swings up to 45°. What is the potential energy at this point, in J? iii. How much energy lost during impact (toughness of specimen), in J?
From the shear stress - shear strain diagram shown below, all the following are true except: Shear Stress (MPa) 500 450 400 350 300 250 200 150 100 50 0. 0.2 0.4 0.6 0.8 1.2 1.4 1.6 1.8 Shear Strain (rad) Shear Stress-Strain Curve for Brass Select one: O a. Shear stress and Shear strain are 430 MPa and 1.72 rad at fracture. O b. Shear stress and Shear strain are 250 MPa and 0.05 rad at Yielding. Oc. The elastic zone ends at a shear stress of 400 MPa and shear strain of 1 rad Od. The ultimate Shear stress and Shear strain are 430 MPa and 1.72 rad.
At higher temperature, strength and strain hardening are increased, whereas, ductility is decreased which permits greater plastic deformation True False O Saaly i The strength constant (C) is increased with increasing of temperature True O False O The metal is becoming weaker as strain increases, this is because of .strain hardening (work hardening) property True O False O ly The engineering stress and strain are defined relative to the instantaneous area and length of test specimen True O False O In sheetmetal working processes, the surface area-to-volume ratio of .w.p. is low True O False O aly ihi Determine the value of the strain-hardening exponent for a metal that will cause the average flow stress to be 70% of the final flow stress after deformation 0.444 0.421 0.422 0.428 aaly i For pure copper (annealed), the strength coefficient = 330 MPa and strain-hardening exponent = 0.52 in the flow curve equation. Determine the average flow stress that the metal experiences if it is…
Q2/ Aluminum tensile specimen with 12.5mm diameter, a gauge length of 50.8mm and the final diameter was 10.5mm. • Plot the engineering stress-strain curve and the true stress- strain curve. Determine proportion limit, young's modulus, the yield point, the ultimate tensile strength, the failure stress on drawing? • Determine Ductility? • Determine Resilience modulus and toughness modulus? 0.006 0.008 0.012 0.017 Strain mm/mm Apparent Stress N/mm 100 0.004 0.22 0.25 0.27 150 200 290 325 480 450 410 True stress N/mm 100.1 150.3 201 326 400 500 550 620