Consider a material with the stress-strain diagram shown where the yield point is 400 MPa (similar to a generic metal, but approximated to make the calculations easier). The material is stressed to 900 MPa. What is the change in the modulus of resilience? σ (MPa) 1200- 800- 400- a more realistic curve 0.10 0.20 0.30 0.40

Consider a material with the stress-strain diagram shown where the yield point is 400 MPa (similar to a generic metal, but approximated to make the calculations easier). The material is stressed to 900 MPa. What is the change in the modulus of resilience? σ (MPa) 1200- 800- 400- a more realistic curve 0.10 0.20 0.30 0.40

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A polypropylene has the following tensile creep compliance measured at 40 °C: D(t) = 1.2 x t0.1 GPa-1 where t is expressed in seconds. It is subjected to the following tensile stress sequence at 40 °C. Find the tensile strain at 3200 sec. Stress (MPa) 1.5 1.0 0.5 1000 2000 3000 Time (s)
Consider a material with the stress-strain diagram shown where the yield point is 400 MPa (similar to a generic metal, but approximated to make the calculations easier). The material is stressed to 900 MPa. What is the change in the modulus of resilience? 1200- 800 σ (MPa) 400 a more realistic curve 0.10 0.20 0.30 0.40 ε
Determine the tensile yield strength (0.2% offset) and the maximum strength of a metal alloy having the following tensile stress-strain diagram. 600 500 400 500 300 400 300E 200 3200 100 100E 0.000 0.002 0.004 0.006 Strain ol 0.00 0.16 0.20 0.08 Strain 0.04 0.12 Select one: O The tensile yield strength Sy = 290 Mpa and the maximum strength Smax = 500 Mpa. O The tensile yield strength Sy = 170 Mpa and the maximum strength Smax = 400 Mca. G The tensile yield strength Sy = 200 Mpa and the maximum strength Smax = 500 Moa. O Tne tensile yield strength Sy = 390 Mpa and the maximum strength Smax= 500 Mpa. The tensile yed strength Sy = 150 Mpa and the maximum strength Smax = 250 Mpa. Stress (MPa) Stress (MPa)
2. The stress-strain behavior of a ductile cast iron of diameter 15.8mm and a gauge length of 60.80mm is shown below, 400 300 200 100 0.00 0.10 Strain Determine the following: (a) the modulus of elasticity (b) yield strength at a strain offset of 0.002. Stress (MPa)
You must perform mechanical tests with a linear elastic material (the material follows Hooke's law) applying forces (tension) in the range 0 to Fmax/2 for Sample A and between 0 to Fmax for Sample B. The samples are made of same material but have different geometries (see illustration). (a) Which of the two samples receives the maximum stress (σmax)? (b) Which of the two samples will have the larger length change (ΔLmax)? (c) Plot the expected curves for the two samples in the force-length and stress-strain planes. (d) Clearly indicate the values that the variables force, length, stress, and strain take at the beginning and end of each curve.
Question 2 A material with the given stress-strain curves is loaded in tension. Loading process COMPLETELY STOPS at B. When stress is 700 MPa and during the Re-load process, Find: 1. The longitudinal and lateral strain 2. Change in diameter a (MPa) 1000 800 dy= 600 300 150 D. 0.02 0.03 0.04 0.023 e(mm/mm) 0.01 €y = 0.006 7 MPa 90 80 70 60 50 40 30 20 10 T = 73 Oy =0.0013 = 0.54 0.73 Y (rad) Yu
A 1.6 ft long rod is made from the material, having the elastic modulus of E = 176 ksi and the yield strength of Sy = 1.04 ksi. The material has the stress-strain curve shown below. 1600 1400 1200 2 1000 800 600 400 200 0.5 1 1.5 Strain, percent By what amount must the rod be stretched from its original length for it to begin yielding? (Express your answer using whole numbers.) AL = mils Stress, psi
Consider a material with the stress-strain diagram shown (similar to a generic metal, but approximated to make the calculations easier). The material is stressed to 900 MPa. What is the new modulus of toughness? σ (MPa) 1200- 800- 400- a more realistic curve 0.10 0.20 0.30 0.40 ε
Using the equations of strain in isotropic elasticity, find the stress tensor that cause the following strain state determined from an experiment (material has Young’s modulus of 190 GPa): ?? = 0.001 0.001 0 0.001 −0.002 0.0005 0 0.0005 0shear moduli is 70GPa.
You need the shear modulus for a particular material in order to calculate shear strain for a known applied shear shear stress. You can't find shear modulus for the material, but you can find elastic modulus (200 GPa) and Poisson's ratio (0.3). Which of the following could you use as the shear modulus for your calculations? 200 GPa O 60 GPa O 77 GPa O 154 GPa
2) The stress-strain diagram for an alloy specimen having an original diameter of 0.5 in. and a gage length of 2 in. is shown in the figure below. TENSILE STRESS (MPA) 450 400 350 300 250 200 150 100 50 Part A 0 0 STRESS VS. STRAIN 0.002 0.004 STRAIN 0.006 Determine the modulus of resilience. Show units. Part B Determine the modulus of elasticity of the material. Part C Estimate the Yield Strength of the material. 0.008 0.01
Young's modulus of elasticity and Poisson's ratio of a material are 1.25×10^5 MPa and 0.34 respectively. The modulus of rigidity of the material is