Co(II) was used as an internal standard to analyze a sample of Ti(IV) with atomic absorption spectroscopy (AAS). A standard mixture containing 1.22 ug Co/ml and 2.20 ug Ti/mL measured by AAS produced a signal-to-signal ratio of 2.35 Ti : 1.00 Co. A mixture was prepared by combining 6.00 mL of a Ti(IV) solution of unknown concentration with 4.00 mL of a 12.4 ug/mL solution of Co(II). The absorbance of the mixture at the Ti(IV) wavelength was 0.104 and the absorbance at the Co(II) wavelength was 0.189. Determine the concentration, in moles per liter, of Ti(IV) in the original unknown solution. concentration: M Ti(IV)

Co(II) was used as an internal standard to analyze a sample of Ti(IV) with atomic absorption spectroscopy (AAS). A standard mixture containing 1.22 ug Co/ml and 2.20 ug Ti/mL measured by AAS produced a signal-to-signal ratio of 2.35 Ti : 1.00 Co. A mixture was prepared by combining 6.00 mL of a Ti(IV) solution of unknown concentration with 4.00 mL of a 12.4 ug/mL solution of Co(II). The absorbance of the mixture at the Ti(IV) wavelength was 0.104 and the absorbance at the Co(II) wavelength was 0.189. Determine the concentration, in moles per liter, of Ti(IV) in the original unknown solution. concentration: M Ti(IV)

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter1: Introduction

Section: Chapter Questions

Problem 1.9QAP

See similar textbooks

Similar questions

A student wanted to determine the level of lead in amoxicillin powder, so he transferred 148 mg of the powder to 200 ml volumetric flask and completed the volume volumetrically, then he transferred 5 ml of the obtained solution to 50 ml volumetric flask and completed the volume properly, and read the absorbance of the obtained solution on AAS. The reading was 0.48. and the calibration equation was: "Y =12.25 x- 0.05" (concentration microg./mL). Calculate the content of lead in amoxicillin as "ppm"? O a. 326.5 O b. 605.0
A student wanted to determine the level of lead in amoxicillin powder, so he transferred 148 mg of the powder to 200 ml volumetric flask and completed the volume volumetrically, then he transferred 5 ml of the obtained solution to 50 ml volumetric flask and completed the volume properly, and read the absorbance of the obtained solution on AAS. The reading was 0.48. and the calibration equation was: "Y =12.25 x- 0.05" (concentration microg./mL). ?"Calculate the content of lead in amoxicillin as "ppm 326.5.a O 605.0 .b O 60.5.c O 17.5.d O 584.7.e O أخل اختياري
The standard curve was made by spectrophotographic analysis of equilibrated iron(III) thiocyanate solutions of known concentration. You are asked to analyze a Fe(SCN)2+ solution with an unknown concentration and an absorbance value of 0.392. The slope-intercept form of the equation of the line is y = 4538.1x +0.0077. The unknown was analyzed on the same instrument as the standard curve solutions at the same temperature. What is the Fe³+ concentration of the unknown solution? [Fe³+] = mol/L Absorbance Iron(III) thiocynate standard curve 1.0 V 0.5 0.0001 Fe³+ concentration (M) 0 0.0002
A student mixed 5.00mL of 0.0020M Fe(NO3)3, 3.00mL of 0.0020M KSCN, and 3.00mL of distilled water. The mixture reacted to form a reddish solution indicating that FeSCN2+ was formed, according to the equation below. An absorbance of 0.21 was measured for this solution in a Spectrophotometer set at a wavelength of 447nm. Fe³+ (aq) + SCN (aq) FeSCN2+ (aq) A calibration curve was used to find the equilibrium concentration of the product of this reaction: y = 1895x + 0.027 Calculate the equilibrium concentration of the Fe³+ Report your answer to 4 sig figs
A mixture is prepared by combining 10.72 mL of 2.52 x 10-3 M Fe(NO3)3 with 10.00 mL of 1.76 x 10-3 M KSCN. The solution turns red due to the formation of FeSCN2+. The absorbance is measured and, using a calibration plot, the [FeSCN2+] at equilibrium is found to be 2.25 x 10-4 M.Complete the following ICE table Fe3+ + SCN- ⇌ FeSCN2+ initial (M) (A) (B) (C) change (M) (D) (E) (F) equilibrium (M) (G) (H) (I) What is the value of Kc?
A standard solution was put through appropriate dilutions to give the concentrations of iron shown in the table that follows. The iron(II)-1,10-phenanthroline complex was then formed in 25.0-mL aliquots of these solutions, following which each was diluted to 50.0 mL. The following absorbances (1.00-cm cells) were recorded at 510 nm: Calculate the concentration, in ppm, of a sample with an abosrbance of 0.829. Fe(II) concentration (ppm) A510 4.00 0.160 10.0 0.390 16.0 0.630 24.0 0.950 32.0 1.260 40.0 1.580
A food supplement is analyzed by Atomic Absorption Spectroscopy to know its Ca content. A 10 ppm standard registers an absorbance of 0.448. A 4.45 g sample is calcined, the ashes are dissolved with 10 mL of acid, and the solution is finally made up to 50 mL; the absorbance reading was 0.325. How many mg of Ca are in 100 g of the dietary supplement?
In the process of performing a spectrophotometric determination of Fe, an analyst prepares a calibration curve using a single-beam spectrometer, such as a Spec-20. After preparing the calibration curve, the analyst drops the cuvette used for the method blank and the standards. The analyst acquires a new cuvette, measures the absorbance of the sample, and determines the %w/w Fe in the sample. Will the change in cuvette lead to a determinate error in the analysis? Explain.
The validation process comprises four main steps that are : hardware validation, software validation, method validation and system suitability. To evaluate a spectrophotometer’s accuracy by measuring absorbance, a solution of 60.06 mg/L K2Cr2O7 in 0.0050M H2SO4 was carefully prepared together with a 0.0050 M H2SO4 as a reagent blank. If the spectrometer’s signal is properly calibrated, it has been reported that this solution should provide an absorbance of 0.640 +- 0.010 at wavelength 350 nm. Which one of the validations mentioned above had been involved in this process? Explain your choice
Atomic emission spectroscopy and the method of standard addition are used to determine the Na+ concentration and its uncertainty in an unknown sample. Increasing amounts of a 1.75 ug/mL standard Na+ solution are added to a series of volumetric flasks containing 15.00 mL of the unknown solution. The volumetric flasks are then diluted to a final volume of 200.0 mL. Atomic emission spectroscopy is then used to measure the emission intensity of each solution. Unknown volume Standard volume Final volume Emission (mL) (mL) (mL) intensity 15.00 0.00 200.0 351.0 15.00 5.00 200.0 494.0 15.00 10.00 200.0 642.0 15.00 15.00 200.0 807.0 15.00 20.00 200.0 948.0 Based on the data in the table, determine the original concentration of Nat and its uncertainty in the unknown sample. Report the uncertainty with three significant figures. concentration: ug/mL µg/mL
Chemistry Atomic absorption analysis of Zn gave a calibration best fit line of A=0.670(ppm Zn) The detection limit was determined for this analysis using a 0.020 ppm Zn solution. The standard deviation of the absorbances for 11 samples of the solution was found to be 1.560 x 10-3 and the slope of the calibration curve was 0.026. Calculate the detection limit, Cq, (in units of ppm) for this instrument. Give your answer to 3 places after the decimal place.
Chemistry What is the formula to calculate the concentration of BSA in the sample. The absorption coefficient at 280nm: k1^mg/ml = 0.7 [mL/mg.cm].