A circular tube AB is fixed at one end and free at the other end. The tube is subjected to axial force at joint B. If the outer diameter of the tube is 5 in. and the thickness is3- in., calculate the maximum normal stress in the tube (in ksi). (Include the sign of the value in your answer.)A6 fted = 5 in.ВV8 kipst= 3/4 in.2.5 in.ksi

Answered: Image /qna-images/answer/4689770d-e863-4978-9030-77c2ea3e6569.jpg

circular tube AB is fixed at one end and free at the other end. The tube is subjected to axial force at joint B. If the outer diameter of the tube is 5 in. and the thickness is in., calculate the maximum normal stress in the tube (in ksi). (Include the sign of the value in your answer.)

circular tube AB is fixed at one end and free at the other end. The tube is subjected to axial force at joint B. If the outer diameter of the tube is 5 in. and the thickness is in., calculate the maximum normal stress in the tube (in ksi). (Include the sign of the value in your answer.)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.11P: A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The...

See similar textbooks

Related questions

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11633 N force. - 540…

A: P= 11633 N Width of the cross section, b= 60 mm Height of the cross section, h= 180 mm

Q: A thin cylindrical pressure vessel with closed-ends is subjected to internal pressure. The ratio of…

A: Given Data⇒ circumferential (hoop) stress longitudinal stress

Q: A hollow cylinder of external diameter 50 mm and internal diameter 30 mm is subjected to tensile…

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023N force. E4.png…

Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…

A: Given data: - The pressure inside vessel is P = 150 psi. The length of the vessel is L ft. The…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by…

Q: The rectangular piece of wood, 50 mm by 100 mm, is used as a compression block. The grain of the…

A: To find largest axial force P

Q: The assembly in Figure consists of a light rigid bar AB, pinned at O, that is attached to the steel…

Q: A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown…

A: For solution refer below images.

Q: The bolt shown on the picture is subjected to total tensile force of 90 kN. Determine the tensile…

Q: A wooden bar is subjected to a tensile stress of 5 MPa. What will be the values of normal and shear…

A: Given data: The tensile stress in wooden bar is σ = 5 MPa. The angle between the section and the…

Q: 1. In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

Q: A circular tube AB is fixed at one end and free at the other end. The tubeis subjected to axialforce…

A: In this question, we determine the maximum normal stress Maximum normal stress, σ=PA here, P is…

Q: stress in the segment QR

A: Given; A bar having cross-sectional area(A)=700 mm2Various loads at the positions indicated at the…

Q: A aluminum tank with a wall thickness of 2.2mm and radius of 145mm is 2m long was pressurized to…

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force.

A: The stress due to normal force on the beam can be determined as,

Q: The structure shown below is hinged to fixed supports at A and C. The bars are each 4 in. by 4 in.…

A: To find maximum tensile stress

Q: Question 3 A steel rod 20 mm in diameter passes centrally through a steel tube of 25 mm internal…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

Q: A load of 7,000 N acts on the machine part shown in Fig. 5a. The machine par thickness of 15 mm…

Q: A bar ACB has is subjected to an external load at C, and it is supported either end by a cable as…

Q: For the figure shown below. Calculate the increase in vertical stresses (Ac) at point A at depth of…

Q: A Portable Crane will be designed as shown in Figure which is able to withstand dynamic loads. The…

Q: A machine having a mass of 9555 kg is supported by three solid steel rods arranged as showed in the…

Q: The vertical load P acting on the wheel of a traveling crane is 13,000 lb. What is the average shear…

Q: ABCD rigid rod is supported as shown in the figure. 40 degrees increase in temperature in the case…

A: Given data, Increase in temperature, ∆T = 40° α1 = Thermal expansion of rod 1 = 16.9×10-6/°C α2 =…

Q: A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm.…

A: Write the given data. t=15 mmD=460 mmH=2.5 mσL=120 MPaσc=50 MPa

Q: If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the B…

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are…

Q: A circular rod of diameterd and length 3d is subjected to a compressive force F acting at the top…

Q: The solid rod shown in Fig. has a radius of 0.75 in. If it is subjected to the force of 800 lb,…

A: Given Data The radius of a solid rod, r=0.75 in load, P=800 lb

Q: Calculate the average stress in section a-a of the junction shown in the figure when applying force…

A: Let us assume that the diameter of the bolt is d in mm.

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have a square…

A: Calculate tension in AB for moment equilibrium about C T x 6 = 20 x 9.5 T = 31.6666 N

Q: A tractor weighing 80 kN was lifted by 3 cables as shown in the figure. Calculate the stress on the…

A: Given: W=Mg = 80 kN The given system will have four forces to be in equilibrium. The equilibrium…

Q: An iron column of annular cross section has an outer diameter of 200mm and is subjected to a force…

Q: Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure.…

Q: If the flat link shown below has an allowable tensile stress of 75 MPa, then a force P 1800 N will…

Q: A steel bar has a uniform cross sectional area of 300mm². Calculate the stress at member AB 1.6m…

Q: The section of a crane hook is rectangular in shape whose width is 30 mm and depth is 60 mm. The…

A: Given that , width = 30mm depth = 60mm centre of curvature of the section is at a distance =125 mm…

Q: Find the hoop stress acting on a cylinder with the following information:

A: To find Hoop stress Acting on cylinder

Q: An axial force P = 450 kN is applied to the knuckle joint shown with the pin diameter d equal to…

A: Given data An axial force is applied to the knuckle joint P = 450 kN diameter d = 20mm. To…

Q: The solid rod shown in Fig. has a radius of 0.75 in. If it is subjected to the force of 800 lb,…

A: Given: Diameter of the rod (D)=1.5inForce (F)=800lb

Q: The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are…

Q: Determine stress in cylindrical rod of diameter 6 in . Tensile force applied 150 lb

A: Given data : The value of tensile Force=P The value of diameter of cylindrical rod=d To find :…

Q: For the pin connection shown, determine the normal stress acting on the gross area, the normal…

A: Given data Given force system

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

A circular tube AB is fixed at one end and free at the other end. The tube is subjected to axial force at joint B. If the outer diameter of the tube is 5 in. and the thickness is
3
- in., calculate the maximum normal stress in the tube (in ksi). (Include the sign of the value in your answer.)
A
6 ft
ed = 5 in.
В
V8 kips
t= 3/4 in.
2.5 in.
ksi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.