Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint. Assume pin diameter of 10 mm, 40 mm wide gap link, 12 mm thick bracket, and 3550N tensile load. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box ● ● ●

Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint. Assume pin diameter of 10 mm, 40 mm wide gap link, 12 mm thick bracket, and 3550N tensile load. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box ● ● ●

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.13P: Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses...

See similar textbooks

Similar questions

2. Calculate the shear stress in a simple pin joint, assuming pin diameter of 10 mm and 3550N compressive load on the link. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box
PRELIMINARY DISCUSSIONS PME 412 - MACHINE DESIGN 1 PROBLEM: Find the values and plot the distribution of stress over the cross section of the upright of the figure. Locate the point of zero stress. 9,000 N 60 mm thick - 100 mm -50 mm
Problem 1-3 The Cartesian components of stresses at a point are given as belou : O = 7, 0y = 6, oz = 5, Tyy = 2, Tyz = – 2, Tz = 0 MPa %3D %3D Determine the values of principal stresses.
1cm t1 (cm) P 3,2 cm t2 (cm) t1 (cm) 1 cm 20 cm Ь (ст) P = 20t %3D Dp=1,6 cm
A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness of 0.085 in. Its length is 14.5 in. What axial com- pressive force would cause the cylinder to shorten by 0.005 in.? What is the resulting stress in the 3-25. aluminum?
Calculate the maximum and minimum normal stresses experienced by the lever indicated in the image.
3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mm
HOW TO SOLVE: Draw the FBD of one member Solve for the bearing force. Section one bold and solve internal forces. Solve for the normal and shear stress in the bolts. Solve for the bearing stress in the members due to the nuts. Solve for the bearing stress in the members due to bolts. ANSWERS: bearing stress of bolt= 7.96 MPa, T; shear stress of bolt= 13.78 MPa; bearing stress (max)= 18.04 MPa
A square pedestal has glued parts at joints t, r, e, and s. Plane t-r-e-s is at anole of 30° from the vertical axis Given the following data: allowable pressive stress of 5.2 MPa in glued joint and Shear stress of 3.5 MPa. If the axial pedestal force is 36 kN. determine the safe width dimension in mm and the angle in degrees if the maximum shear stress will occur to the plane.
please box in the following answers: normal stresses for beam AB and BC (mid section) normal stresses for beam AB and BC (at connections A and C) shear stress for pin A, B and C bearing stress along member AB and BC at pin section for A and C 600mm Flat end 40 mm FRONT VIEW d-25 mm d-25 mm 50 mm 125 mm 30 mm 25mm ,20 mm TOP VIEW OF ROD BC -800 mm Q-30 kN TOP VIEW OF BOOM AB d=25mm Flat end Q-30KN 20mm 20 mm END VIEW 600 mm 50 mm 20 mm 800 mm 30 AN 1
10/10 find the tensile stress in upper plate in section 3-3 5. 1 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 2) 300 mm 8 mm
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)