(b) Using a synchronous binary counter as shown in Figure Q2(b), design and draw a counter to generate the following repeating sequences 2 to 14 repeatedly for a free running clock. If the circuit happens to enter any of the states 15 or 0 or 1, what are the next states of your circuit? Syn. Binary Counter Q3 Q₂ Q₁ ← CLK 8 Qo Asyn. clear Syn. load D3 D₂ D₁ Do ↑ ↑ ↑ ↑

(b) Using a synchronous binary counter as shown in Figure Q2(b), design and draw a counter to generate the following repeating sequences 2 to 14 repeatedly for a free running clock. If the circuit happens to enter any of the states 15 or 0 or 1, what are the next states of your circuit? Syn. Binary Counter Q3 Q₂ Q₁ ← CLK 8 Qo Asyn. clear Syn. load D3 D₂ D₁ Do ↑ ↑ ↑ ↑

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

1. Consider the CRC generator shown below. Determine the output of the CRC circuit (i.e. Q4 Q3 Q2 Q1 Q0, expressed as a decimal number) for the input sequence "1010" (input one bit at a time, left to right). Assume the CRC circuit is initialized to state 11111. D Q0 Q2 Q4 Q1 Q3 Clock - Data In
Draw logic diagram for half adder and full adder circuit using Logisim Software
What’s the difference between sequential and combinational circuits? Also explain what’s the difference between positive and negative edge clock inputs for the flip-clops.
To reset IC chips in a system at power-on, the chips must be powered on and working already. That is to say that the reset signal needs to be after the power-on time. Assume that you need to generate a reset signal 1 ms after power-on using an RC circuit, what will be roughly the values of the resistor and capacitor?
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
Q1: Design and Draw the timing Diagram of 3-bit Asynchronous down counter if you know that the clock type is given in the figure below?
Design a combinational circuit that takes 3-bit pattern as input and outputs binary code of bit position of the first 1' in the pattern reading from MSB (2nd position) to LSB (0th position).An additional output variable V is required along with binary code to indicate that the binary code is valid or note i.e., if the input pattern is '000' then the output V should be '0' to indicate that the binary code is not indicating the bit position of first 1' and we don't care about the binary code if V = 0. Design the required circuit using dual 4x1 MUXS and minimum additional logic.Available resources along with dual 4x1 MUXS are NOT gates, 2-input(AND, OR, NAND, NOR) gates.
c. Sketch the zero-pole plot and the direct form II diagram of the completed design out of part b. d. Calculate and sketch the output sequence after feeding x [n] into this system.
Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.
Binary 4-bit Asynchronous down Counter and explain how it functions, find real life applications
Design a counter that counts 1-2-3-5-7 Please explain the following:state diagram state table simplification Logic circuit digital design
1What will be the state of a MOD64 counter after 90 input pulses if the starting state=000000?A.100100B.011010C.010110D.011100 2.A MOD 32 counter is holding the count 101112. What will the count be after 31 clock pulses?A.10100B.10010C.10000D.10110