1. You are required to perform an energy analysis of aCarnot Vapor Cycle and an ideal Rankine Cycle whichoperate on the same compression and expansionpressures. The analysis should include but not limitedto:a. State diagrams of the cycles, andb. Sample calculations of the performance of thecycles in regard to thermal efficiency and workratio with appropriate assumptions.Compare and comment on your findings.

Answered: Image /qna-images/answer/0a58ff94-fc0d-479b-9b6c-5e715a1f0015.jpg

Answered: a. State diagrams of the cycles, and b.…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Sketch a carefully drawn temperature-entropy diagram of a Camot cycle. Explain as many features of the graph as you possibly can.
(17 blanks) Calculate the efficiency of the Carnot Engine for ideal gas. Consider the figure below for a complete cycle of Carnot engine, where the cycle goes from ad->ab->bc->cd
Given a Brayton cycle, with a pressure ratio equivalent to 12, as shown in the figure, determine its thermal efficiency, in %. Use Standard Cold Air Assumption Method (constant specific heats at room temperature, 25ºC).
A four-cylinder spark-ignition engine with a compression ratio of 8 has a pistonswith a bore of 9 cm and a stroke of 10 cm. The air pressure at the beginning of thecompression is 98 kPa, and the temperature is 37 oC. The engine may be modeled by theair-standard Otto cycle. The maximum cycle temperature is 1700 oK. If the engineproduces 75 kW of power, determine a) the heat supplied per cylinder; b) the thermalefficiency; and c) the rpm required.
Provide the given, manual step by step solution, and diagram. A Carnot cycle has an efficiency of 60 %. The heat added is 1000 KJ.What is the heat rejected from the cycle?
Example-1: In a Brayton cycle, the air at the inlet is at 27°C, 0.1 MPa. The pressure ratio is 6.25 and the maximum temperature is 800°C. Find (a) The compressor work per kg of air (b) The turbine work per kg or air (c) The heat supplied per kg of air (d) The cycle efficiency. Solution: T₁ = 27°C = 300 K P₁ = 100 kPa r₂ = 6.25 T3 = 800°C = 1073 K T N T Isobaric qin qout
(b) Derive an expression for thermal efficiency of ideal Brayton cycle
On the diagram below sketch a basic Rankine cycle with superheating. Assume that there are irrevesibilities in the turbine and pump. Identify the device associate with each process. Make sure to label: the states and include important features, e.g. lines of constant temperature, volume, pressure, entropy, vapor dome, etc.
Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
1. A reversible Carnot engine has a hot reservoir at T=880K and a cold reservoir at T=340K. The working gas (1mole) has a heat capacity Cv,m=5R/2. - Draw the cycle on a PV plot, marking the temperatures at each point a, b, c and d. The volumes are Va=4L, Vb=15L, Vc=32L and Vd=7L. - State for each path a -> b, b -> c, c-> d, d -> a, whether process is adiabatic, isotopic, isothermal, and/or isobaric, and whether it's an expansion or a compression. - Calculate the work and q (heat) associated with each path. - What is the efficiency of this engine? Thanks a lot.
How can we increase the efficiency of the Rankine cycle? Discuss one method where the changes to be done in the ideal Rankine cycle for the sake of efficiency enhancement. Show the changes in schematic and T-S diagram.
In an air standard Brayton cycle the air enters the compressor at 0.1 MPa, 25 ∘C. The pressure leaving the compressor is 1 MPa. and the maximum temperature in the cycle is 1200 ∘C. Assume a compressor efficiency of 80%, a turbine efficiency of 85%, and a pressure drop between the compressor and turbine of 30 kPa. Use the PG model. a) Determine compressor work (w_C), b) Determine the turbine work (w_T), c) Determine the cycle efficiency (n_th,Brayton).

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

a. State diagrams of the cycles, and b. Sample calculations of the performance of the cycles in regard to thermal efficiency and work ratio with appropriate assumptions. Compare and comment on your findings.