A long embankment 30 m wide is to be built on ground. The net vertical pressure applied by the embankment (assumed to be uniformly distributed) is 90kpa. The soil profile and stress distribution beneath the center of the embankment is also shown. The value of mv for the upper clay is 0.35m2/MN, and for the lower clay mv=0.13m2/MN. Tthe permeabilities of the cllays are 10-10m/s and 10-11m/s for the upper and lower soil respectively. Determine the final settlement under the center of the embankment due to consolidation

A long embankment 30 m wide is to be built on ground. The net vertical pressure applied by the embankment (assumed to be uniformly distributed) is 90kpa. The soil profile and stress distribution beneath the center of the embankment is also shown. The value of mv for the upper clay is 0.35m2/MN, and for the lower clay mv=0.13m2/MN. Tthe permeabilities of the cllays are 10-10m/s and 10-11m/s for the upper and lower soil respectively. Determine the final settlement under the center of the embankment due to consolidation

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.12P

See similar textbooks

Similar questions

Q: For the soil profile shown in figure. Determine: The effective stress (o') at level (A). Soil 1 k = 0.2 cm/sec Y sat = 19 kN/m³ Soil 2 k = 0.4 cm/sec Y sat = 21 kN/m³ Datum D EL + 2.0 m EL 0.0 m EL - 1.0 m EL - 4.0 m EL - 10.0 m
Effective Stress in Soil Problem 1. The water table in a certain deposit of soil is at a depth of 2m below the ground surface. The soil consists of clay up to depth of 4m from the ground and below which lies sand. The clay soil is saturated even above the water table: Clay strata: ? = 30%,?? = 2.72 Sandy Strata: ? = 26%, ?? = 2.64 1. Compute the total pressure. 2. Compute the pore water pressure. 3. Compute the effective stress pressure at a depth of 8m below the ground surface
A uniform soil deposit has a dry unit weight of 15.6 kN/m³ and a saturated unit weight of 17.2 kN/m³. The groundwater table is at a distance of 4 m below the ground surface. Point A is at a depth of 6 m below the ground surface. If the water table rises by 3.5 m, determine the change in effective stress at A. Indicate if it is maintained, increased or decreased.
3 m 1 m A seepage flow condition is shown in the figure. The saturated unit weight of the soil Yar =18 kN/m2. Using unit weight of water, Y, = 9.81 kN/m³, the Soil 5 m effective vertical stress (expressed in Y sat = 18 kN/m kN/m?) on plane X-X is --.-X 1 m X - 2 m
Compute geostatic stress at point A y= 15.0 kN/m³ V Y= 16.8 kN/m³ Y= 17.2 kN/m³ 2.0 m 2.5 m 3.6 m 10.9 m SC 1.6 m B SM Silty sand CL Clay
Q4 A 0.7m long soil specimen is subject to a steady-state flow, as shown in Figure Q4. The saturated unit weight of the soil is 20 kN/m³. Determine the following: Datum Y 0.8 m Figure Q4 Water B d) Total stress (kPa) at point A, B and C. e) Porewater pressure (kPa) at point A, B and C. 0.3 m 0.3 m 0.4 m
The deposit of silt having specific gravity of 2.65 is located at the bottom of a river. It wasalso found out that it has a void ratio of 0.55. If the river is 5 m deep, compute the effectivevertical stress at a point 3 m below the bottom of the river.
A clay formation having a depth of 4 m. underlies a sand formation having a depth of 3 m. The dry unit weight of sand is 16.5 kN/m3 and the saturated unit weights of clay and sand are 20.4 kN/m3 and 19.6 kN/m3 respectively. The groundwater table is at the interface of the sand and clay. Compute the effective stress at the bottom of clay. Use 3 decimal places in MPa.
A. Compute the effective stress at the bottom of the clay. B. If the water table rises to the level of the soil surface, what is the effective stress at the bottom of the clay? Fground surface Y-15.6 kN/m Yrar-16.6 KN/m3 4 m water table Clay 5 m:
3. For the system shown, L = 1.20m, h = 2.30m, and y = 1.90m. What is the effective stress 5. From the figure shown. at point A where z = 0.70m? h =1.5m 1.5m Standpipe G=2:68 é 0.5 Saud 2.5m Porous stone valve орen Soil A In flow Yan = 19.5 kN/m Cross - sectional area of tank = 0.6 m? Porous stone Hydraulic conductivity of sand = 0.1 cm/s a. What is the rate of upward seepage of water? b. What would be the critical hydraulic gradient?
Water flows at a rate of 0.09 m3/s upward through a sand sample with a coefficient of permeability of 27 cm/s. The thickness of the soil is 0.24 m and the area is 0.54 sq. m. Saturated unit weight is 18.9 kN/m3. a) Determine the hydraulic gradient (Ans. 0.617) b) Compute the effective stress at the middle of the sample (Ans. 354 N/m2) c) Compute the effective stress at the bottom of the sample. (Ans. 728 N/m2)
A 3 meter thick fill was placed over a 9 meter thick compressible clay. Underlying the clay layer is a very hard impermeable clay. The groundwater table is located on top of the compressible clay. A circular tank 9 meters in diameter transfers a surface contact stress of 45 kPa. Assume for this problem that the settlement of the fill and the very hard clay is small compared to the settlement of the compressible clay. a) Calculate the initial void ratio and saturated density of the compressible clay. b) Divide the compressible layer into two sublayers of equal thickness. The preconsolidation pressure is 100 kPa for the upper sublayer and 160 kPa for the lower sublayer. Calculate the following at the center of each sublayer: the increase in vertical stress caused by the tank underneath its center, and the consolidation setttlement due to the combined effect of the tank and weight of fill. c) How long will it take for 0.18 meters of settlement to occur? d) After 3.6 years, what…