A continuous concrete flooring system consists of a 3-in thick concrete slab supported by 15-in wide integral joists spaced 6 ft on center. The floor slab is loaded with a uniform factored load of 3000 Ib/ft? over a simplý supported span of length L = 20 ft. The concrete has a compressive strength of 3000 psi and depth d can be provided in a single row. Show that Mu s OMn. reinforcement is Grade 60 steel. Calculate the minimum number of # 11 bars at a 24 in from the top face required to support the flexural load. Assume the reinforcement %3D

A continuous concrete flooring system consists of a 3-in thick concrete slab supported by 15-in wide integral joists spaced 6 ft on center. The floor slab is loaded with a uniform factored load of 3000 Ib/ft? over a simplý supported span of length L = 20 ft. The concrete has a compressive strength of 3000 psi and depth d can be provided in a single row. Show that Mu s OMn. reinforcement is Grade 60 steel. Calculate the minimum number of # 11 bars at a 24 in from the top face required to support the flexural load. Assume the reinforcement %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength oMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' = 28 MPa and fy = 413.70 MPa. 750 mm T175 mm 1000 mm 9-36 mm dibmeter bars 350 mm dooo
The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation . Ust Bearing |1000 kN plate Steel- Concrete 300 mm 300 mm Section a-a
Load = 3000 lb Q:Find Stresses at: Section A-B & Section D-C "18.0"- "5,5" Plain Concrete: D Compressive Strength : 280 (Psi) "12.0"- "0.5"-
Figure 2 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform service (unfactored) live load of 1.5 kips/ft. The concrete strength is 3500 psi, and the yield strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load (Table 5.3.1) and strength reduction factors from AC1318-14. For the midspan section shown in Fig. P4-1b, compute Mn and show that it exceeds Mu. @ (b) 3 No. 9 bars WD = 1.4 kips/ft plus weight of beam 1.5 kips/ft WL H 12 in. 20 ft TT 21.5 in. 24 in. + Figure 2.
Principle of Reinforced/ Pre-stressed Concrete. Please provide clear written solution. Thank you! Calculate the magnitude of a uniformly distributed load (in addition to the beam’s) which will cause the beam section to begin to crack if it has a simple span of 6m. The beam is made of normal-weight concrete with fc’ = 28 MPa.
Give full explanation Awall form 14 ft high is filled with 160 lb per cu ft concrete at a tem perature of 70°F. The concrete is Type I without a retarder. Concrete will be placed with normal internal vibration to a depth of less than 4 ft. The rate of placement is 5 ft per hr. From Table 1, the value of Cw is 1.1 and from Table 2 the value of Cc is 1.0. The rate of placement is less than 7 ft per hr and the place ment height does not exceed 14 ft so calculate the lateral pressure by using appropriate formula.
A doubly reinforced concrete beam of size 250 mm x 500 mm overall depth is reinforced with 2-12 mm dia. bars in compression zone and 3-20 mm dia. bars in tension zone, each at an effective cover of 40 mm. The grade of concrete and steel are M20 and Fe415 respectively. The strain in compression steel will be [Take stress in compression steel as 345 MPa]
A simply supported beam shown in figure 1, carries an uniform service (unfactored) superimposed deadload of 1.4 kips/ft. plus its own weight and a liveload of 1.5 kips/ft. The concrete strength is 3,500 psi, and the yield strength of the reinforcement is 60,000psi. The concrete is normal- weight concrete. Use the load and strength reduction factors from ACI Code. Compute the design strength or capacity at the midspan of the beam and check if it is safe or adequate to resist the factored service moment. a). 220 kips-ft., safe Figare li wds 14 kipplr.; We= 1,5 kips /. し,vbv b). 336 kips-ft., safe 215" c). 128 kips-ft., inadequate 3 ho. 9 ars d). 255 kips.ft., adequate Solution:
Referenced concrete When designing the same bim Why is the load in the case of moment greater than the load in the case of shear?
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f'c = 21 Pa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars Determine the limiting tensile steel ratio for a tension controlled condition in positive or negative bending with the given material strengths.
Q2// A floor system consists ofconcrete slab supported by continuous beam h = 140mm , bw = 300mm,d = 550mm, f 28MPA, fy = with: %3D 420MPа. Determine the steel reinforcement required at mid span of interior beam to resist service dead load moment Ma = 320KN.m and service live load moment M = 250 kN.m %3! %3D 8m + 3m 4 3m 3m 1-1
Give the comparison of the Pre – Stressed Concrete andthat Cast in Place concrete.