Answered: A concentrated load of 22.5 KN acts on…

A concentrated load of 22.5 KN acts on t surface of a homogeneous soil mass of large extent.Find the stress intensity at a depth of 15 metres and directly under the

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.12P: Refer to Problem 6.1. Using Eqs. (6.3) and (6.29), estimate the average stress increase (Δσav) below...

See similar textbooks

Related questions

Q: A concentrated load of 2000 kN is applied at the ground surface. Determine the vertical stress at a…

A: Solution Given Data Concentrated load= 2000 kN

Q: Problem 1. The water table in a certain deposit of soil is at a depth of 2m below the ground…

A: Saturated unit weight of clay…

Q: A clay formation having a depth of 4 m. underlies a sand formation having a depth of 3, m. 16.5…

A: Depth of clay layer= 4mDepth of sand layer = 3 mUnit Weight of Sand γdry-sand = 16 kN/m3Saturated…

Q: A vertical load of 300 kN is applied to a 1.5 m * 1.5 m area at the ground surface that is level.a.…

A: Solution Given Data Vertical Load Q=300 KN Square Footing =1.5m*1.5m L=1.5 m B=1.5 m

Q: A soil stratum has two layers a 4m-thick dry sand underlain by a 5m–thick saturated sand. Dry unit…

A: Given data: γdry=16.21 kN/m3γsat=20.88 kN/m3σ'=104 kPa at the bottom of saturated layer

Q: A uniformly distributed line load is acting on the ground surface. Based on the Boussinesq's theory,…

Q: A flexible rectangular area 3m by 2m is subjected to a uniformly distributed load of q = 200 kN/m2.…

Q: soil profile consists of a sand layer underlain by a clay layer, as shown. If the degree of…

Q: A concentrated load of 1800 kN is applied on the surface of the ground. By using Boussinesq…

Q: Ex: For a uniformly loaded area having R=3 and load q= 100 kN/m², estimate the increase in the…

Q: The soil profile consists of a 16 m layer of sand, 12 m layer of clay and incompressible bedrock.…

A: gyebehejis

Q: C 6 m B A 5 m 3 m 6 m 3 m Fiq 23 - Prob 23

Q: In a drained triaxial compression test conducted on dry sand, failure occurred when the deviator…

Q: A soil deposit exists in an area where the ground surface is level. The unit weight for the soil is…

A: The given data is shown below:

Q: circular area having a radius of 3 m, carries a uniformly distributed load of 96 kPa is applied to…

Q: A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the…

Q: 2- Point loads of magnitude 100, 200, 300 and 400 lbs. act at A, B, C, and D, respectively.…

A: Given Data: The point loads A, B, C and D are given as: QA = 100 lbsQB = 200 lbsQC = 300 lbsQD = 400…

Q: A circular area of 10 m in diameter on the ground surface carries a uniformly distributed load of 6…

Q: Consider a circularly loaded flexible area on the ground surface. Given: radius of the circular…

A: The increased in stress under the soil is happen by lots of situation like excess load over the…

Q: A concentrated load of 2000 kN is applied at the ground surface. Determine the vertical stress at a…

A: solution Given point load Q=2000KNa. Verticle stress directly at depth z=6mts from the point load…

Q: The water table in soil deposit is 2 m below the ground surface. The soil above the water table has…

Q: A sediment settling lagoon has a depth of water of 4 m above the clay base. The clay layer is 3 m…

A: given data :- A sediment settling lagoon has a depth of water of 4 m above the clay base. The clay…

Q: A saturated site is underlain by a 5m thick layer of clay with undrained strength = 80 kPa, OCR = 2,…

A: The values given in the question are as follows: The thickness of clay layer(hc)=5 m Undrained…

Q: For soil profile and uniformly distributed loaded area shown below, find the increases in the…

A: Given data in question Unit weights Depths Cross section dimensions of circle and rectangle. To…

Q: A circular area having a radius of 3m carries a uniformly distributed load of 96 kPa is applied to…

Q: A 3 m-thick sand layer is underlain by a deep bed of clay where the water content is 29%. The water…

Q: A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the…

Q: EX: The uniformly distributed vertical load on the rectangular area is q1 =100 kN/m², and the…

Q: A seepage flow condition is shown in the figure. The saturated unit weight of the soil Yet = 18…

A: Given data, Ysat = 18 kN/m. Unit weight of water, Yw = 9.81 kN/m, To find out the vertical stress…

Q: A layer of saturated clay 6 m thick is underlain by rock and is subjected to an average increase in…

Q: A soil profile is shown in Figure 1. Assuming the water table is located at the surface and the…

A: Solution: When the water table is at surface: Points Total stress Effective stress Pure water…

Q: Figure 1 illustrates surcharge of 90 kPa was on the surface over an extensive area for a road…

A: Given data: yw=9.81 kN/m3.

Q: Figure below shows an embankment load on a silty clay soil layer. Determine the stress increase at…

Q: Consider a circularly loaded flexible area on the ground surface. Given that the radius of the…

A: This problem is related to vertical stress topic from Soil Mechanics. In this problem there are…

Q: Fground surface Y-15.6 kN/m Year-16.6 KN/m 4 m waler table Clay 5 m Y=17,8 kN/m Compute the…

Q: The total horizontal and vertical stresses at a point X in a saturated sandy medium are 170

Q: In an area where the ground surface is level, the underlying soil has a unit weight of 16 kN/m3.…

A: Given: Unit weight of soil = 16 kN/m3Stress acting depth=5 m

Q: A clay layer 5.61 m. thick rests beneath a deposit of submerged sand 6.16 m. thick. The top of the…

Q: Problem 1. The water table in a certain deposit of soil is at a depth of 2m below the ground…

A: Clay strata: Water content=30%, Specific gravity=2.72 Sand strata: Water content=26%, Specific…

Q: Problem 1. The water table in a certain deposit of soil is at a depth of 2m below the ground…

A: To find total stress, pore water pressure and effective stress at a depth of 8m

Q: . Three point loads, 19000, 20000 and 18000kN, act in line 8 m, 6m apart near the surface of a soil…

A: Given three point loads that are 8m and 6m apart near the surface of soil mass. It is required to…

Q: An embankment load on a silty clay soil layer as shown below. Determine the stress increase under…

A: The given data is: γ=18 KN/m3Depth of consideration z=6 m

Q: Calculate the effective stress at Point C. Assuming soil is dry above water table and saturated…

Q: In a drained triaxial compression conducted on dry sand, failure occurred when the deviator stress…

Q: Problem 1: Point loads of magnitude 100, 200, and 400 kN act at A, B, and C, respectively. Determine…

Q: for a soil profile consists of a two- way drainage clay layer of 5 meters with W.T at N.G.S., total…

A: For any soil when it is subjected to external loading or surcharge loading it shows the long term…

Q: A vertical load of 260 kN is applied to a 1.2 m * 1.2 m area at the ground surface that islevel.…

A: Given: The load is 260 kN. The area of the surface is 1.2 m x 1.2 m. The depth is 1.5 m.

Q: Soil with a unit weight of 16.97 kN/m^3 is loaded on the ground surface by a uniformly distributed…

A: Given:- q=300 KN/m2r=d2=42=2 mz=5 m

Q: onsider the soil profile shown in Figure 1.4: How high should the groundwater table rise/drop so…

A: calculate effective stress at c so calculate dry unit weight of dry sand…

Q: A 30-kN concentrated load is imposed at the surface of a granular soil deposit. Determine the…

A: (a) The expression for the vertical stress by Boussinesq condition is given by, ∆σv=QZ2IB…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

100%

A concentrated load of 22.5 KN acts on the
surface of a homogeneous soil mass of
large extent. Find the stress intensity at a
depth of 15 metres and directly under the
load.
Use Boussinesq"s equations.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refer to Problem 6.1. Using Eqs. (6.3) and (6.29), estimate the average stress increase (Δσav) below the center of the loaded area between depths of 3 m and 6 m. 6.1 A flexible circular area is subjected to a uniformly distributed load of 150kN/m2 (Figure 6.2). The diameter of the load area is 2 m. Determine the stress increase in a soil mass at points located 3 m below the loaded area at r = 0. 0.4 m, 0.8 m, and 1 m. Use Boussinesq’s solution. Figure 6.2 Increase in pressure under a uniformly loaded flexible circular area
The soil profile at a site consists of 10 m of gravelly sand underlain by a soft clay layer. The water table lies 1 m below the ground level. The moist and saturated unit weights of the gravelly sand are 17.0 kN/m3 and 20.0 kN/m3, respectively. Due to some ongoing construction work, it is proposed to lower the water table to 3 m below the ground level. What will be the change in the effective stress on top of the soft clay layer?
The soil profile at a site consists of 10 m of gravelly sand underlain by a soft clay layer. The water table lies 1 m below the ground level. The moist and saturated unit weights of the gravelly sand are 17.0 kN/m3 and 20.0 kN/m3, respectively. Due to some ongoing construction work, it is proposed to lower the water table to 3 m below the ground level. What will be the change in the effective stress on top of the soft clay layer?
Q: For the soil profile shown in figure. Determine: The effective stress (o') at level (A). Soil 1 k = 0.2 cm/sec Y sat = 19 kN/m³ Soil 2 k = 0.4 cm/sec Y sat = 21 kN/m³ Datum D EL + 2.0 m EL 0.0 m EL - 1.0 m EL - 4.0 m EL - 10.0 m
A soil fails under an axial vertical stress of 100kN / (m ^ 2) in unconfined compression test. The failure plane makes an angle of 50 degrees with the horizontal. The shear parameters 'c' and angle of internal friction'' respectively will be
A uniform soil deposit has a dry unit weight of 15.6 kN/m³ and a saturated unit weight of 17.2 kN/m³. The groundwater table is at a distance of 4 m below the ground surface. Point A is at a depth of 6 m below the ground surface. If the water table rises by 3.5 m, determine the change in effective stress at A. Indicate if it is maintained, increased or decreased.
A 30-kN concentrated load is imposed at the surface of a granular soil deposit. Determine the subsurface vertical stress created at depths of 5 m and 10 m directly beneath the loading and at a horizontal distance 5 m from the line of application (5 m and 10 m depths) for:(a) Boussinesq conditions.(b) Westergaard conditions.**Please include units and conversion. Explain also if possible.
A 30-kN concentrated load is imposed at the surface of a granular soil deposit. Determine the subsurface vertical stress created at depths of 5 m and 10 m directly beneath the loading and at a horizontal distance 5 m from the line of application (5 m and 10 m depths) for:(a) Boussinesq conditions.(b) Westergaard conditions.
FRepuble of th e PhINppines IFUGA O STATE UNIVERSITY Lamur, ugao PROBLEM SET #4 EFFECTIVE STRESSES IN SOIL Problem 4. A 20m thick submerged saturated clay layer has water content of 57%. The specific gravity of the solid particle is 2.84. 1. Determine the density of the clay in kg/m3. 2. Determine the total vertical stress at the bottom of the clay layer in kpa. 3. Determine the effective vertical stress at the bottom of the clay layer in kpa. GE
consolidated drained triaxial test was conducted on a granular soil. At failure (σ1^')/(σ3^' ) = 4.0. The effective minor principal stress at failure was 100 kN/m2. Compute angle of friction^' in degrees. a. 39 b. 41 c. 37 d. 35
A Dry sand 6m Ydry = 16.5 kN/m³ B Groundwater table Saturated sand Ysat = 19.25 kN/m³ 13m Dry sand Saturated sand Clay Calculate the following: a. Effective stress at point A in kPa. b. Effective stress at point B in kPa. c. Effective stress at point C in kPa.
Give the correct option In a drained triaxial test on consolidated clay the stress and angle are as follows: Deviator stress is 20 lb/in2 and friction angle is 21°. Calculate the effective confining pressure at failure?a) 21 lb/in2 b) 22.2 lb/in2 c) 25.4 lb/in 2 d) 17.9 lb/in2