7-27. The bar has a cross-sectional area A and is subjected to the axial load P. Determine the average normal and average shear stresses acting over the shaded section, which is oriented at 0 from the horizontal. Plot the variation of these stresses as a function of 0 (0 ≤ 0 ≤ 90°). P 07 Prob. 7-27 7 A P

7-27. The bar has a cross-sectional area A and is subjected to the axial load P. Determine the average normal and average shear stresses acting over the shaded section, which is oriented at 0 from the horizontal. Plot the variation of these stresses as a function of 0 (0 ≤ 0 ≤ 90°). P 07 Prob. 7-27 7 A P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

9-17. Determine the equivalent state of stress on an element at the same point which represents (a) the principal stress, and (b) the maximum in-plane shear stress and the associated average normal stress. Also, for each case, determine the corresponding orientation of the element with respect to the element shown and sketch the results on the element. 75 MPa + 125 MPa 50 MPa
7-70. The assembly consists of three disks A, B. and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d, within the support space, and the diameter d, of the hole in the bottom disk. The allowable bearing stress for the material is (o.)al - 125 MPa. 350 MPa and allowable shear stress is Tali - 140 kN 20 mm
9-38. Determine the principal stresses acting at point A of the supporting frame. Show the results on a properly oriented element located at this point. 12 mm A 130 mm- + B 150 mm -800 mm- ев -15 mm 300 mm 6 kN Prob. 9-38 5 9
9-39. Determine the principal stresses acting at point B, which is located just on the web, below the horizontal segment on the cross section. Show the results on a properly oriented element located at this point. Although it is not very accurate, use the shear formula to calculate the shear stress. 12 mm A 150 mm 130 mm- B A -800 mm- 300 mm B -15 mm 6 kN Prob. 9-39 5
P7-8. A loading causes the member to deform into the dashed shape. Explain how to determine the normal strains ECp and eAn. The displacement A and the lettered dimensions are known. B. -2 L-
7-70. The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter di of the top disk, the diameter dy within the support space, and the diameter dy of the hole in the bottom disk. The allowable bearing stress for the material is (a.)ler - 350 MPa and allowable shear stress is Tlon - 125 MPa. 140 kN d. 20 mm 10 mm
*7-36. The pedestal has a triangular cross section as shown. If it is subjected to a compressive force of 2250 N, specify the x and y coordinates for the location of point P(x, y), where the load must be applied on the cross section, so that the average normal stress is uniform. Compute the stress and sketch its distribution acting on the cross section at a location removed from the point of load application. X 75 mm 300 mm 150 mm 2250 N Prob. 7-36 P(x,y) y
7-70. The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter di of the top disk, the diameter dz within the support space, and the diameter dy of the hole in the bottom disk. The allowable bearing stress for the material is (7,)alow - 350 MPa and allowable shear stress is Tlon - 125 MPa. 140 kN 20 mm 10 mm
R7-5. Determine the average punching shear stress the circular shaft creates in the metal plate through section AC and BD. Also, what is the bearing stress developed on the surface of the plate under the shaft? 40 kN - 50 mm - Ti0 mm -60 mm -120 mm
7-54. The lever is attached to the shaft A using a key that has a width d and length of 25 mm. If the shaft is fixed and a vertical force of 200 N is applied perpendicular to the handle, determine the dimension d if the allowable shear stress for the key is Tallow 35 MPa. a A d a 20 mm = 500 mm Prob. 7-54 200 N
9-41. The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point B, which is located on the outer surface of the pipe. Prob. 9-41 12 in. N Z A B- x C y 12 in. 60 lb 30°
9-23. The wood beam is subjected to a load of 12 kN. If grains of wood in the beam at point A make an angle of 25° with the horizontal as shown, determine the normal and shear stresses that act perpendicular and parallel to the grains due to the loading. 12 kN -2m-+-1m-t- 25° 75 mm -4 m- Prob. 9-23 300 mm 200 mm