1. A 2-wire d.c. distributor A B is fed at both ends at the same voltage of 230 V. The length of thedistributor is 500 metres and the loads are tapped off from the end A as shown below:Load :100 A60 A40 A100 ADistance :50 m150 m250 m400 mIf the maximum voltage drop of 5-5 V is to be allowed, find the X-sectional area of each conductor andpoint of minimum potential. Specific resistance of conductor material may be taken as 1-73 x 10* 2 m.[1-:06 cm' ; 250 m from A

1. A 2-wire d.c. distributor A B is fed at both ends at the same voltage of 230 V. The length of the distributor is 500 metres and the loads are tapped off from the end A as shown below: Load : Distance : If the maximum voltage drop of 5-5 V is to be allowed, find the X-sectional area of each conductor and point of minimum potential. Specific resistance of conductor material may be taken as 1-73 x 10*2m. 100 A 60 A 40 A 100 A 50 m 150 m 250 m 400 m [1-06 cm' ; 250 m from Al

1. A 2-wire d.c. distributor A B is fed at both ends at the same voltage of 230 V. The length of the distributor is 500 metres and the loads are tapped off from the end A as shown below: Load : Distance : If the maximum voltage drop of 5-5 V is to be allowed, find the X-sectional area of each conductor and point of minimum potential. Specific resistance of conductor material may be taken as 1-73 x 10*2m. 100 A 60 A 40 A 100 A 50 m 150 m 250 m 400 m [1-06 cm' ; 250 m from Al

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.9MCQ: Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated...

See similar textbooks

Similar questions

Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
conclusion and observation in Kirchhoff's Current Law and Kirchhoff's Voltage Law
Identify the correct junction and loop rules, the solve for the missing currents using Kirchhoff’s Rules
What will be the value of the twiddle factor: W42
Q1- The given ferromagnetic core relative permeability is 800. Determine the total reluctance of the core. 35 cm 10 cm 20 cm 5 cm 15 cm 45 cm 15 cm 15 cm 10 cm
If the core of LVDT is at the middle, then the output voltage will be a. maximum b. minimum c. Output voltage is no relation with core position d. 0
use kirchhoffs Junction rule and loop rule to solve for currents I1 , I2 and I3..
In transformer, the eddy current loss can be minimized by O using thin size copper conductors O using magnetic material with low permeability laminating the core O using magnetic material with high permeability
A certain laminated core has a permeability of 2,500. The length is 5.5 cm and the cross section is 2.1 sq. cm. What is its reluctance? Draw the diagram for the question
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
To size conductors and overcurrent devices for source circuits, you must multiply the module string short-circuit current by ______________________.